Part #2 Effective Stress (kPa) Void Ratio (%) The following are the results of laboratory consolidation test conducted on clayey soil sample. Determine, graphically, the compression and recompression indices, Cc, C, of this soil. Using Casagrande's method, determine graphically the preconsolidation pressure. 0.891 54 0.866 107 0.841 214 0.802 429 0.737 858 0.653 1716 0.560 3432 0.467

Part #2 Effective Stress (kPa) Void Ratio (%) The following are the results of laboratory consolidation test conducted on clayey soil sample. Determine, graphically, the compression and recompression indices, Cc, C, of this soil. Using Casagrande's method, determine graphically the preconsolidation pressure. 0.891 54 0.866 107 0.841 214 0.802 429 0.737 858 0.653 1716 0.560 3432 0.467

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following results were obtained in a series of consolidated undrained test on saturated clay: Sample No. All round pressure (03 ) (kN/m²) Deviator stress Pore water pressure (kN/m³) (kN/m²) 1 17 140 12 44 160 20 3 56 169 22 Determine the strength parameters c, c', o and '.
Question Table 1 gives data from a standard shearbox(direct shear) test on a sample of 125g of dry sand. The initial dimensions of the sample were 60mmx60mm on plan x20mm in height. The test was caried out at a constant normal effective stress of 50k:Pa. Take the specific gravity of the soil grains Gs=2.65. Plot graphs of (a) shear stress t against shear strain y; (b) volumetric strain evol against shear strain y; (c) specific vohume v against shear strain y. (d) Comment on these graphs and estimate the peak and critical state effective angles of friction of the soil. Table 1: Shearbox Data Relative horizontal Upward vertical movement Shear stress t (kPa) displacement x (mm) of shearbox lid y (mm) 0.00 0.000 0.02 0.002 19 0.04 0.008 34 0.06 0.016 43- 0.08 0.026 47 0.20 0.064 56 0.32 0.128 51 0.48 0.192 46 0.64 0.256 41 0.80 0.288 37 0.96 0.320 34 1.12 0.321 33
The results obtained from a series of CU test on a soil gave the following results : CCU = C'CU = 0 cu 15°; 'cu = 30° CU A sample of this soil was tested in a CU test under a cell pressure of 150 kN/m². Determine (i) deviator stress at failure (ii) pore water pressure at failure (iii) minor principal effective stress at failure (iv) major principal effective stress at failure (v) the magnitude of Skempton's pore water pressure parameter(at failure) A
The laboratory consolidation test is conducted on a clay sample. The following data results were obtained P1 =55 kPa P2 = 130 kPa e1= 0.95 e2= 0.80 Thickness of the sample of clay= 35mm Time for 50% consolidation = 3.0 min Tv= 0.197 a. Find the coefficient of volume compressibility b. Determine the coefficient of consolidation if a sample of clay was drained on both sides c. Compute the hydraulic conductivity of the clay
A) The results of two consolidated-drained triaxial tests on clay are given below in Table 2. Table 2: Results of CDT tests. Specimen Chamber Pressure I II 3, kPa 110 220 Deviator Stress 01-03, kPa 220 400 a) Calculate the shear strength parameters of the soil. b) What are the normal and shear stresses on a plane inclined at 38° to the major principal plane for Specimen I? c) What are the normal and shear stresses on the failure plane at failure for Specimen II? B) The laboratory test results of a standard Proctor test are given in the following table.
A series of direct shear tests has been performed on a dense well-graded sand. All tests were performed on 3.00-in. diameter, 1.25 in. tall cylindrical samples, and were run slowly enough to produce drained conditions. The results of these tests are summarized in the following table: Test Number Normal Load (lb) Shear Load at Failure (lb) 1 100 84 2 200 159 3 400 319 Assuming the shear area remains constant during the test, determine the effective cohesion and effective friction angle from these test results. What values of these parameters would you expect? Are the test results consistent with your expectations? What values would you use for design?
: In a tri-axial test of a silty soil, the sample failed at normal stress of 475 kPa and a shear stress of 350 kPa. Which of the following gives the angle of internal friction? Compute the angle that the failure plane makes with the x-axis. Compute the maximum failure stress.
Q₂/ From the result which obtained from consolidation test on a sample of clay soil at depth (3.5 m). Show if the soil is (N.C.C) or (O.C.C), if you know: (y sat = 18.82 kN/m³). Pressure Void ratio 0 0.903 25 0.865 50 0.843 100 0.795 200 0.730 400 0.651 800 0.555 1600 0.468 400 0.501 100 0.547 25 0.583 0 0.612
A consolidated-drained triaxial test was conducted on a normally consolidated clay. The results were as follows: Determine: a. Angle of friction, f? b. Angle u that the failure plane makes with the major principal plane c. Normal stress, s?, and shear stress, tf , on the failure plane
An undisturbed soil sample, 100 mm in diameter and 200 mm high was tested in a tri-axial machine. The sample failed at an additional axial load of 3 kN with a vertical deformation of 20 mm. The failure plane was inclined at 50 deg. to the horizontal and the cell pressure was 300 kPa. a.) Determine the angle of internal friction. b.) Determine the deviator stress in kPa. c.)Determine the cohesion of the soil in kPa.
A consolidated undrained tri-axial test was conducted on a normally consolidated clay sample and the results are as follows: chamber confining pressure = 110kpa deviator stress at failure = 96kpa pore water pressure = 66kpa these test results were used to determine the drained friction angle of the soil. compute the deviator stress in (kpa) at failure when the drained test was conducted with the chamber confining pressure changed to 163kpa.
A consolidated-undrained test was conducted on a normally consolidated clay sample. The results are as follows: Undrained angle of friction = 38.65°, Drained angle of friction = 62.59°, Deviator stress at failure = 509 lb/ft^2. Determine the pore water stress at failure in lb/ft^2.