Consider a convective heat transfer system, like the heat exchanger described above. Pertinentproperties and their units are:Pipe diameterThermal conductivity of fluidFluid velocityFluid viscosityFluid densityFluid heat capacityHeat transfer coefficientdkVHРCphLenergy /L tᵒL/tM/LtM/L³energy/Mᵒenergy/L² tᵒNote: "°" indicates units of temperature. Do not decompose "energy" into its fundamental units.Leave it as "energy", even though it is derived from mass, length, and time.Identify the important dimensionless groups. h, Cp, and should appear only once.

Answered: Image /qna-images/answer/924e2891-0cc5-48e4-8d74-0490a3b3e7a2.jpg

Fluid heat capacity Heat transfer coefficient Cp h energy/Mº energy/L² to Note: "°" indicates units of temperature. Do not decompose "energy" into its fundamental units. Leave it as "energy", even though it is derived from mass, length, and time. Identify the important dimensionless groups. h, Cp, and v should appear only once.

Fluid heat capacity Heat transfer coefficient Cp h energy/Mº energy/L² to Note: "°" indicates units of temperature. Do not decompose "energy" into its fundamental units. Leave it as "energy", even though it is derived from mass, length, and time. Identify the important dimensionless groups. h, Cp, and v should appear only once.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
A particle of mass 0.102 kg is rotating at 840 rpm at a radius of 135 mm. At t=2 the radius begins to expand at a rate of 14 mm.s-1. What is the radial force at t=1.9s [N] What is the arc length traveled by the mass at t=1.9 s? [m] What is the transverse force on the mass at t=4s? [N]
Pressure drop AP depends on four variables: the diameter of the pipe D, the density of the fluid p, the kinematic viscosity of the fluid v and the mean velocity v. Applying Buckinham's Pi Theorem, a dimensionless pi-group can be identified using the following power product: [AP] = [D]ª[p]b[v][v]ª. Which of the following statements in term of [T] is correct? Select one: O [T]: -2 = -c-d [T]: -1 = -c-d [T]: -2 = -c-2*d [T]: -2 = -2*c-d [T]: -2=-c+d
A particle of mass 133 kg is traveling on a constant radius 1.1 m with a angle of 0.23*sin(0.35t). 1. What is the transverse speed at 2.6 seconds? [m.s-1] 2. What is the radial force at 2.6 seconds? [N] 3. What is the transverse force on the particle at 2.6 seconds? [N
Thermal conductivity k is a measure of the ability of a material to conduct heat. For conduction heat transfer in the x-direction through a surface normal to the x-direction, Fourier’s law of heat conduction is expressed as: Q=-kA.dT/dx where ?̇ is the rate of heat transfer and A is the area normal to the direction of heat transfer. Determine the primary dimensions of thermal conductivity (k). Look up a value of k and verify that its SI units are consistent with your result. Write a set of primary SI units for k.
c) When small aerosol particles move through air or water, the Reynolds number is very small (Re < 1). Such flows are called creeping flow. The aerodynamic drag on an object in creeping flow is a function only of its speed, V some characteristic length scale, L of the object and fluid viscosity, µas indicated in Figure 11. Use dimensional analysis to generate a relationship for Fp as a function of the independent variables. The dimensions of Fp are MLT2. FD L Figure 11
Your assigned value of y is 30 The following fluids specific heats are used. Fluid Comments X (liquid) Y (ideal gas) Z (liquid) Cp 4.2 kJ/(kg °C) 1.01 kJ/(kg °C) 2.03 kJ/(kg °C) does not change phase R = 287 J/(kg K) does not change phase Note: if any of these problems is impossible, state impossible, rather than a numerical answer. 1) A shell-and-tube heat exchanger with two shell passes and four tube T shell, in passes is used to heat (0.5 + y/40) kg/s of liquid Z from 10°C to 50°C. using 1.5 kg/s of liquid X entering at Trube,in (80 + y/2)°C. The over-all heat transfer coefficient is U = (150 – y) Figure 1: For use in Problem 5 W/(m² °C). a. Find the exit temperature of Fluid X: Tx,out = °C (± 1°C) b. Find the required heat transfer surface area: A = m² (± 1%)
The gravitational constant g is 9.807 m/s² at sea level, but it decreases as you go up in elevation. A useful equation for this decrease In g is g= a - bz, where z is the elevation above sea level, a = 9.807 m/s², and b=3.32 x 10-61/s². An astronaut "weighs" 80.0 kg at sea level. [Technically this means that his/her mass is 80.0 kg.] Calculate this person's weight in N while floating around in the International Space Station (z=325 km). If the Space Station were to suddenly stop in its orbit, what gravitational acceleration would the astronaut feel Immediately after the satellite stopped moving? The person's weight in N while floating around in the International Space Station Is The astronaut feels a gravitational acceleration of m/s² N.
An object is left to cool down in air and the following temperature data were recorded during the process. t [min]=0,1,2,3,4,5 T[celcius degree] = 100,88,82,72,70,65 (a) Represent this data by a 2^ order polynomial b) Predict how long it would take for the object to reach to 30 °C.
Case 1: Volume = 60 mL Mass of empty beaker = 40 g Total Mass, Liquid Mass, Liquid Mass, Volume, V Density [kg/m³] Specific No mtot [g] mlig (g] mlig [kg] [m³] Gravity, SG 1 91 95.2 3 97 4 100 5 103 6 104.8 7 106.3
Suppose you're converting a bill of materials for machining feedstock from the British gravitational (U.S. system) of units to International System (SI) units. Your goal is to have all of the material quantities in kilograms. Your bill of materials lists values for required weights of brass rod in pounds. To convert to these values to kilograms you first you divide by gravitational acceleration in feet per second squared to get a mass in slugs, then convert slugs to kilograms using standard conversion factors. Group of answer choices True False