The formula below finds the Reynold's number, Re, a measure of the characteristics of fluid flow in a pipe. Dvp Re If D (diameter of the pipe) is measured in meters, v (flow velocity) is measured in meters/second, pis density measured in kilograms/meter, and Re is dimensionless, what are the units for u, the dynamic viscosity? b. The dynamic viscosity of ethyl alcohol is 2.0 x 105 bf-s/ft?. Convert this units you found in Part a. а. SI

The formula below finds the Reynold's number, Re, a measure of the characteristics of fluid flow in a pipe. Dvp Re If D (diameter of the pipe) is measured in meters, v (flow velocity) is measured in meters/second, pis density measured in kilograms/meter, and Re is dimensionless, what are the units for u, the dynamic viscosity? b. The dynamic viscosity of ethyl alcohol is 2.0 x 105 bf-s/ft?. Convert this units you found in Part a. а. SI

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine whether the following equations are dimensionally homogeneous. pl t = mf represents an…

A: Given: The expression is t=plmf. l is acceleration, p is pressure, m is weight, t is time, f is…

Q: (3) Use the following graph to answer the questions on this page. The total time is 0.4 seconds.…

A: Solution:

Q: A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure…

A: A constant volume gas thermometer is typically made up of a bulb filled with a predetermined amount…

Q: b) Complete the cells in the following table of properties of water. In the last column describe the…

A: The compressed liquid is a state or the phase of the fluid when its temperature is less than the…

Q: The power P required for operating a pump depends on the diameter of the pump D, the pressure rise…

Q: I need help on this question: This question is to see to validate or the two methods using a data…

A: Given : To find : Validate the equations

Q: Use the following TTT Diagram for the following questions: 800 A 1400 -Eutectoid temperature 700 A…

A: Answer is given in next step.

Q: Determine whether the following equations are dimensionally homogeneous. h = gt? h represents a…

Q: physical quantities m, r, u, a, and it with dimensions [m] = M, [r]= L, [v] = LT, [a] = LT-2, and…

Q: At low velocities (laminar flow), the volume flow Q through a small-bore tube is a function only of…

A: Given: As stated in the question description, we can express the volume flow rate Q as,…

Q: Question 4.4 A core was mounted in a gas permeameter to measure permeability, and the following…

Q: Independent variables in a turbomachine are the impeller diameter, D, angular speed, ω, and fluid…

A: To perform dimensionless analysis, we use Bukingham's Pi theorem:If we have n variables and k…

Q: Determine whether the following equations are dimensionally homogeneous. 2ph3 f = mh 3t2 f is a…

Q: The following related values of the pressure p in kN/m2 and the volume V in cubic meter where…

Q: Determine whether the following equations are dimensionally homogeneous.

Q: 1.1 s) The overall size of the system (i.e. the shell) is 5.8 inch ID and a 27-inch long tube…

Q: 2. GIVEN: NACA 23112 AND chord is 115 cm Determine: a) Maximum Camber b.) Position of Max. Camber,…

A: NACA Nomenclature

Q: Determine whether the following equations are dimensionally homogeneous. 2ph3 mh + 3t2 f : || f is a…

A: Given equation is f=2ph3l+mh3t2 Here, f is the force, h and l is the velocity, m is a mass, t is a…

Q: In medical literatures, local blood perfusion rate is typically presented as xx ml/(min 100g…

A: Given:To find:Convertthe local perfusion rate into values with unit L/s.

Q: Let the velocity, u (m/s), specific heat, cp (kJ/(kg K)), and temperature, T (K), be used to define…

Q: The correct definition of Dimensional Analysis is: A procedure to find the yield point of a…

A: The correct definition of Dimensional Analysis is:-A methodical process of converting from one set…

Q: Calibrate a vertical cylindrical container medium water inside container, density is 1000 kg/m³.…

A: Density of water, ρ=1000 kg/m3Diamter of the tank, d=14 cm=0.14 mHeight of the tank, H=20 cm=0.20 m

Q: 3. Andrade's equation is a proposed model of the effect of temperature on viscosity written as, H =…

Q: 8478 Btu/ft² - hr °F/in to cal/cm² - s°C/cm 48.94 Btu/ft² - hr ºR to W/m²C 1.835 kW-hr to kcal-s 478…

Q: Question 1 How much energy does the cooling tower remove? Using the information provided in the…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: Determine whether the following equations are dimensionally homogeneous. f = m· a + c · v + k · x f…

A: The dimensions of various term used in the expression are as follows: m·a=kg·ms2=MLT-2 And…

Q: The Wind Tunnel cross section has width, w = 10 inch. Air velocity, V (ft/s) is measured at…

A: We have given

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

2.
The formula below finds the Reynold's number, Re, a measure of the characteristics of
fluid flow in a pipe.
Dvp
a. If D (diameter of the pipe) is measured in meters, v (flow velocity) is
measured in meters/second, pis density measured in kilograms/meter, and
Re is dimensionless, what are the units for u, the dynamic viscosity?
b. The dynamic viscosity of ethyl alcohol is 2.0 x 105 Ibf-s/ft?. Convert this to SI
units you found in Part a.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
Please do this carefully.
56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1.60 s 3.62 s 1.52 s 3.44 s 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? O The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquid X is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. 3.
Fill in blank hell
Pressure drop AP depends on four variables: the diameter of the pipe D, the density of the fluid p, the kinematic viscosity of the fluid v and the mean velocity v. Applying Buckinham's Pi Theorem, a dimensionless pi-group can be identified using the following power product: [AP] = [D]ª[p]b[v][v]ª. Which of the following statements in term of [T] is correct? Select one: O [T]: -2 = -c-d [T]: -1 = -c-d [T]: -2 = -c-2*d [T]: -2 = -2*c-d [T]: -2=-c+d
Please do this caredully.
Thermal conductivity k is a measure of the ability of a material to conduct heat. For conduction heat transfer in the x-direction through a surface normal to the x-direction, Fourier’s law of heat conduction is expressed as: Q=-kA.dT/dx where ?̇ is the rate of heat transfer and A is the area normal to the direction of heat transfer. Determine the primary dimensions of thermal conductivity (k). Look up a value of k and verify that its SI units are consistent with your result. Write a set of primary SI units for k.
**Problem 1.15 Suppose you wanted to describe an unstable particle, that spon- taneously disintegrates with a "lifetime" t. In that case the total probability of finding the particle somewhere should not be constant, but should decrease at (say) an exponential rate: too P(t) = | V(x,1)1²dx = e=1/*. -0- A crude way of achieving this result is as follows. In Equation 1.24 we tacitly assumed that V (the potential energy) is real. That is certainly reasonable, but it leads to the "conservation of probability" enshrined in Equation 1.27. What if we assign to V an imaginary part: V = Vo – ir, where Vo is the true potential energy and r is a positive real constant? (a) Show that (in place of Equation 1.27) we now get dP 21 = --P. dt (b) Solve for P(1), and find the lifetime of the particle in terms of r.
Kinematic viscosity /g of water varies with temperature T as shown in the table. Determine the cubic that best fits the data, and use it to compute / at T = 10°,30°, 60°, and 90°C. by interpolation.)
1. What is a fluid? kg [6 marks] 2. A tank is filled with oil with density p = 830; If the volume of the tank is V = 1.01m³ determine the amount of mass in the tank in kilograms. Show your workings. m³ [6 marks] 3. A pipe of diameter 0.18 m has a flow rate of 0.025 m³/s, what is the average velocity in the pipe? Show your workings. [6 marks] 4. The flow rate in a pipe is 1446 litres per minute, what is this in SI units Show your workings. )? [5 marks] 5. The equation below is a simplified form of the continuity equation. dm dt CV Σmin -Σmout The derivative term with respect to time is which of the following: a. The rate of change of the mass within a given control volume b. Always zero by definition c. Zero for transient time dependant flow conditions d. Zero when the mass flow rate coming into the control volume is smaller than the mass flow rate exiting the control volume e. Zero when the mass flow rate entering the control volume is greater than the mass flow rate leaving the…
The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?
Vibration