Find the original cross sectional area and original length from the given information about a tensile test done on a specimen directly. Conversion to an engineering stress versus engineering strain is straightforward. One simplydivides the measured loads by the specimen cross-sectional area A to obtain the stress, andsimilarly, the displacement is divided by the initial gauge length, L, of the specimen to obtain thestrain. Dimensions for our specimens are shown in Figure 3.2, and all specimens are machined froma 0.125 inch thick sheet.All dimensions to within ±0.005 in.0.250 in. radius0.250 in.1.000 in.-3.750 in.Figure 3.20.375 in.

Given : From the figure, we can see that. initial diameter of specimen, d0 = 0.375 in final or neck…

Answered: Find the original cross sectional area…

Find the original cross sectional area and original length from the given information about a tensile test done on a specimen

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diagram shows a plot from an uniaxial test of an unknown metal. The uniaxial tensile test specimen had an original cross-sectional radius of 3.0 mm, an initial gauge length of 42 mm. At failure, the cross-sectional radius was 1.2 mm. Determine the yield strength of the unknown metal and the true stress at failure.
39)A tensile test specimen has a gage length=3.0 inches and a diameter= .75 inches. Yielding occurs at a load of 38000lbs. The corresponding gage length=3.0103 inches (neglect the .0.2% yield point). The maximum load of 54000lbs is reached at a gage length =3.453 inches. If fracture occurs at a gage length of 3.873inches, determine the percent elongation at fracture (Round to the nearest whole %)
A specimen of diameter and length 10 mm & 100 mm respectively is subjected to tensile test. If the diameter and length at the fracture is 6 mm and 120 mm respectively. Then _________ is the Longitudinal strain
This steel alloy specimen had an original diameter of 12.8 mm and a gauge length of 50.80 mm: i) If it were subjected to a load of 120 kN and then released, what would have been its permanent elongation? Be thorough. ii) If it were subjected to a load of 230 kN and then released, what would have been its permanent elongation? Be thorough.
During a tensile test on a specimen of 100mm^2 cross-section, maximum load observed was 71168N and area of cross-section at neck was 50mm^2. Ultimate tensile strength of the specimen is?
10. A standard steel specimen of 0.504" diameter elongated 0.0125" in an 8" gage length during a test where it was subjected to a tensile force of 6249 lb. If the specimen's gage length was measured to be 8.0025" after the test was over, what was the permanent plastic deformation? What is the elastic deformation and what is the modulus of elasticity of that metal? r PL AE
Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…
Hello, the stress and cycles required for this question is Stress 1 = 420MPa at 7 cycles, Stress 2 = 360MPa at 65 cycles and Stress 3 = 130MPa at 325 cycles. Use the first three cycles (which shows how many cycles at that stress level to failure) to calculate when the specimen will fail if it underwent test of 7 cycles at 420MPa, then undergoes 360MPa for 65 cycles and finally 130MPa at 325 cycles. Will the specimen fail? Please show calculations of failure
When the diameter of a specimen subjected to a twist test increases, the shear stress increases. Select one: O a. False O b. True
At operating stress of 420MPa, the number of cycles to fail a specimen is 65 cycles. At operating stress of 360MPa, the number of cycles to fail the specimen is 390 cycles, and at operating stress of 130MPa, the number of cycles to fail the specimen is 11,900 cycles. A test sequence as follows is designed: first, operating stress of 420MPa for 7 cycles, second, operating stress of 360MPa for 65 cycles, and third, operating stress of 130MPa for 325 cycles. Determine at what number of cycle and which operating stress level the specimen would be expected to fail if the above sequence is repeated.
the material had a tensile stress of 67.7 ksi then was unloaded. the original length of the specimen was 5.0 inches. show the line on the diagram you would expect the material to follow as the load was released. estimate the length of the specimen after all load was removed.