figure is subjected to a positive bending moment of 54000 Nm acting around the horizontal neutral axis. Determine the bending stress acting on each of the three infinitesimal areas shown by the heavy dots.

figure is subjected to a positive bending moment of 54000 Nm acting around the horizontal neutral axis. Determine the bending stress acting on each of the three infinitesimal areas shown by the heavy dots.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a B a W B W C b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) b C C P C D P Ľ E d E ·x Ey
The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 16.2 mm, determine the second moment of area of the cross section. Note: Give your answer in mm4 Note: Do NOT include units in your answer. 10MM 150HM 120 MM hmm
The aluminium machine part shown below is subjected to a moment of M = 75 N.m. Determine the bending stress created at points B and A on the cross section. Sketch the results on a volume element located at each of these points. A- 50mm 50mm 100mm 100mm 20mm B- M=8kN-m 20mm
The hollow square cross section shown has a wall thickness, T, of 12.0 mm. Determine the second moment of area of the cross section. Note: Give your answer in mm² Note: Do NOT include units in your answer 100mm Answer: K-T
The beam in (Figure 1) is made from three boards nailed together as shown. If the moment acting on the cross section is M=650N.m determine the resultant force the bending stress produces on the top board. " 20 mm 200 mm M 25 mm 150 mm 20 mm
Pls solve C and D
1. 2. 10 mm 10 mm 3. 5 mm 100 mm A beam section as shown in the sketch is subjected to a bendingmoment of Mx = 4 kN.m and a shear force of V = 2.5KN. 50 mm 100 mm Calculate the position of the centroid and the the second moment of area of the section about the sentroid horizontally. Draw the bending stress distribution through the height of the beam by calculating the bending stress at the critical positions Draw the shear stress distribution trough the height of the beam by calculating the shear stress below the flanges and at the centroid. 4. Draw the stress condition below the flanges, at the centroid and at the top and bottom of the beam.(7) 5. Draw the shearflow through the section. Show calculations
In the figure shown, the aluminum strut has a cross-sectional area in the form of a cross. If it is subjected to the moment M= 8 kN.m: 1) determine the bending stress acting at points A and B, 2) show the results acting on a stress distribution diagram.
The simply supported beam is subjected to the force F = 700 N and the uniform distributed load with intensity w = 150 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(r) and M(x). Take a = 0 at point A. 19 F a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 m 2.6 m 3.12 m Support Reactions The reaction at A is N. The reaction at D is N. Shear Force and Bending Moment Equations In section AB: V(x)= N and M(x)= N-m. In section BC: v(x)- N and M(x)= N-m. In section CD: V(x)- N and M(x)= N-m. A
The simply supported beam is subjected to the force F-600 N and the uniform distributed load with intensity w=450 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(z) and M(2). Take 2 = 0 at point A. 19 W B F 2013 Michael Swanbom BY NC SA D Χ a. -b- - Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value α 4 m b 2 m с 3 m Determine the maximum shear force (magnitude) and its location in the beam, and the maximum bending moment (magnitude) and its location in the beam. Note: On an exam, you may be required to actually sketch the shear and moment diagrams, but there is no reasonable way to assess this on WAMAP. Maximum shear stress: Vmax Maximum bending moment: Max = N located at x = m Nm located at x = m
The aluminum machine part is subjected to a moment of M = 75 N.m. (i) Determinethe bending stress created at points B and C on the cross section; (ii) Determine the maximumtensile and compressive bending stresses in the part.
Below Figure shows the section of an angle purlin. A bending moment of 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the sense of the bending moment is such that both its components Mx and My produce tension in the positive xy quadrant, calculate the maximum direct stress in the purlin, stating clearly the point at which it acts. * 100 mm E 10mm 30 C D -10mm 57 MPa. 89 MPa. Non Above O 72 MPa. 125mm