The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown in Figure 2. If it is subjected to a moment of M = 6.5 kN.m, determine the maximum bending stress in the brass and steel. Also, what is the stress in each material at the seam where they are bonded together? The elastic modulus for the brass is Ebrass = 100 GPa and the elastic modulus for the steel is Esteel = 200GPa. 150 mm B M 175 mm Figure 2 200 mm

The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown in Figure 2. If it is subjected to a moment of M = 6.5 kN.m, determine the maximum bending stress in the brass and steel. Also, what is the stress in each material at the seam where they are bonded together? The elastic modulus for the brass is Ebrass = 100 GPa and the elastic modulus for the steel is Esteel = 200GPa. 150 mm B M 175 mm Figure 2 200 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 The internal bending moment in a beam with a cross sectional area shown in the figure is 500a in the direction shown. Nom Find: a) The centroid of the cross sectional area and, b) the maximum tensile and compressive normal stresses. Make a sketch showing the stress distribution A A -35 mm C2 100 mm C1 = ỹ 5 G0 Na m 25 mm B 50 25 50. mm 'mr mm
An elastomeric bearing pad is used to support a bridge girder as shown. The bearing pad provides flexibility in the horizontal direction to accommodate thermal expansion and earthquake motions. The shear modulus of the bearing pad is G = 1.50 MPa. The beam must not displace horizontally more than 25 mm when a load of P = 45 kN is applied as shown. Determine the maximum thickness t that can be used for the bearing pad. Assume a = 300 mm and b = 420 mm. Answer: tmax = i mm
The cross-sectional dimensions of a beam are shown in the figure. Assume a = 45 mm, b = 75 mm, t = 4 mm and d =55 mm. (a) If the bending stress at point Kis 54 MPa (C), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress at point H. The bending stress is positive if in tension and negative if in compression. IT H Answers: (a) M₂= (b) og = i 945.9 144.881 d N-m MPa
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis (i) The moment of inertia in (mm^4)= ii) The radius of curvature in (mm) = (iii) The maximum bending stress in (N/mm^2)= iv) The bending stress at the point 0.6 cm from the neutral axis in (N/mm^2)=
A beam is loaded as shown in the figure. F = 2200 lb, b = 2 in. and h = 4 in. Determine the maximum shear force in the beam in lb. Determine the maximum bending stress in the beam in psi. Determine the bending stress in a fiber located 0.5 in. from the top of the beam at midspan in psi.
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. The cross-sectional areas of sections AB, BC, and CD are AAB = 0.09 in², ABC = 0.15 in², and Acp = 0.05 in², respectively. The modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. (Figure 1) Figure Aluminum Eal = 10(10³) ksi 2.00 kip -18 in- Copper Ecu = 18(10³) ksi 3.50 kip 13.50 kip -12 in- Steel Est = 29(10³) ksi 1.75 kip 1.75 kip -16 in- 1.50 kip 1 of 1 Part A Determine the normal stress in section AB. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the normal stress in section BC. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. OBC = Submit Part C OCD =…
A beam has a bending moment of 3 kN-m applied to a section with a hollow circular cross-section of external diameter 3.4 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is in (N/mm^2) Answer and unit for part 3 iv) The bending stress at the point 0.6 cm from the neutral axis is in(N/mm^2) Answer and unit for part 4
A simply supported reinforced concrete beam carries a uniformly distributed load of 12 kN/m on a span of 4 m. The beam has a rectangular cross section 250 mm wide by 450 mm deep, with three 20 mm diameter steel bars placed 60 mm from the bottom of the beam, as shown below. The moduli of elasticity for the concrete and steel are 15 GPa and 200 GPa, respectively. Determine the average tensile stress in the steel and the maximum compressive stress in the concrete at the section of maximum bending moment. 450 mm 250 mm 60 mm
A beam has a bending moment of 4.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.1 cm and internal diameter 2.1 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: - The bending stress at the point 0.6 cm from the neutral axis is
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
A composite beam is constructed using a steel plate(0.5 in.x 6 in.) with two wood beams (3in. X 6 in.) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment Mz=60 kip-in. Calculate the maximum tensile and compressive stresses in the wood and steel if Ew= 1500 ksi and Es=29,500 ksi.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.6 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.5 cm from the neutral axis is