Answered: The beam ABCD with a rectangular cross…

The beam ABCD with a rectangular cross section carries the loading shown in the figure. Determine the maximum bending stress in the beam in MPa. 2 kN 50 mm 5 kN • m A D 80 mm B E1.0 m - 1.0 m –

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.12P: The T-beam shown in the figure has cross-sectional dimensions: b = 210 mm, t = 16 mm, h = 300 mm,...

See similar textbooks

Similar questions

Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
The T-beam shown in the figure has cross-sectional dimensions: b = 210 mm, t = 16 mm, h = 300 mm, and A, = 280 mm. The beam is subjected to a shear force V = 68 kN. Determine the maximum shear stress tntijlin the web of the beam.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
Determine the minimum allowable height (h) in mm of the beam shown in the figure if the bending stress is not to exceed 20 MPа. 5 kN 2.5 kN/m 80 mm A E D 1.0 m 1.0 m 2 m
Let a=4 ft, b=6 ft, c=4 ft and w-7.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions a B b W C- C D -X Calculate the reaction forces Ay acting on the beam. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Final answer in kips rounded-off to 1 decimal place
The simply supported beam with following cross section is loaded with concentrated loads and uniform load as shown. Determine a) the maximum tensile and compressive bending stress if P= 150 kip and w = 10 kip/ft, and b) the allowable uniform load w if the allowable bending stress is 24 Ksi and P = 15w. 3.169 in and c 1.5 inch Draw the FBD and calculate the reaction forces and shear and bending moment diagram. Draw the stress profile. Determine the maximum bending moment and its location 0.25 in. 3 ft 3 ft -0.25 in. 3 in. 10 ft 0.25 in. 3 in. -
I am struggling with this question
Question contains a hinge in the middle. Find the shear force and the bending moment at the Figure 3 shows the external loading conditions of a beam that cross-section A and B. A hinge 1.5m 1.5m 1m 1m 2m Fig. 3. The benan contains a hinge in the midle.
Consider an 8-m long simply supported T-beam with overhangs loaded as shown below. 200 mm w kN/m 50 mm 50 kN-m 50 kN-m 200 mm 2 m 4 m 2 m 50 mm 1. Determine the location of the neutral axis measured from the top of the beam and the moment of inertia (in mm4) of the section about its neutral axis. Draw the shear and bending moment diagrams. Annotate all relevant values and distances. Determine the magnitude of the maximum negative 2. moment. Determine the minimum allowable strength of the beam in tension and the minimum allowable strength of the beam in compression. 3. Determine the maximum allowable load, w (in kN/m), that can be applied pn the beam. 4. B.
A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress (in Pa) at the top of the of the beam on a section 2.82 m from A if P = 4212 N, W = 1939 N/m, a = 1.12 m, b = 2.1 m, c = 1.25 m, L = 83 mm and h = 218 mm. Round off the final answer to two decimal places.
Q1) A beam has a loading system as shownin the figure below. (1) draw the shear dia gram (2) m om ent diagram X 5 m 20 kN 30 kN JI0 KN -2m 4 m LE 4 m 12 m RA With the same beam in ql computefor the second moment of area using the cross-section below. consider the non-shaded region. 20 mm 200 mm B 20 mm h=14O mm 300 mm N.A. 20 mm