(14) Find the total shear load on each of the three bolts for the connection shown in the figure and compute the significant bolt shear stress and bearing stress. Find the second moment of area of the 8-mm plate on a section through the three bolt holes, and find the maximum bending stress in the plate. (Ans/ 1.48(10) mm4, 110 MPa ) Holes for M12 x 1.75 bolts mm thick |12 AN 36 32 64 Dimensions in millimeters 36 -200 Column

(14) Find the total shear load on each of the three bolts for the connection shown in the figure and compute the significant bolt shear stress and bearing stress. Find the second moment of area of the 8-mm plate on a section through the three bolt holes, and find the maximum bending stress in the plate. (Ans/ 1.48(10) mm4, 110 MPa ) Holes for M12 x 1.75 bolts mm thick |12 AN 36 32 64 Dimensions in millimeters 36 -200 Column

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the magnitude of maximum normal stress, in section a-a in numeric value without units upto 4 digits after decimal point, but with correct sign. Enter only MPa: 200 mm 200 mm R. Section a-a 400 N 800 N
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-section. M=5 kN.m 30° 10 mm 40 mm 10 mm -40 mm 30 pfn 10 mm 10 mm
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
Determine the maximum bending stress in the given figure below.
For the figure shown below. Find the maximum allowable value of P if the bending stresses are not exceeding 3.5 KN/m² in tension and 8KN/m² in compression 0.015m 0.015m 2P |4P ЗР 0.2m . 0.25m 0.02m 2m A A 2m.
Total Change in length?
In the figure, two planks are fastened together with a sheet plate with a thickness of 4 mm. Since 1 kN load is applied to the plank; a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and the bearing stress on the plate (the thread bottom diameter of the M10 bolt is approximately 8 mm)
Calculate Stresses at (x, y, z)= (0", 0.5", 0"). No Shear and Moment Diagrams.
The bar in the figure below is made from standard acrylic plastic (E = 2960 MPa). Compute the total change in length, δof the shaft due to the loadings shown.
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1