1 kN12. A cantilever beam AB, loaded by a uniform load and a320 N/mconcentrated load, is constructed of a channel section.Find the maximum tensile stress o, and maximum compressive stressac if the cross section has the dimensions indicated and the moment ofinertia about the z axis (the neutral axis) is I = 130 cm*.Note: The uniform load represents the weight of the beam.1.5 m15 mm[ Ans : a, = 105.8 MPa ; 6e = 28.8 MPa ]55 mm

Answered: Image /qna-images/answer/888a6c57-5245-4a20-abe4-c9eec765ee10.jpg

12. A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress o, and maximum compressive stress o, if the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is I = 130 cm". Note: The uniform load represents the weight of the beam. [ Ans : G, = 105.8 MPa ; 6. = 28.8 MPa ]

12. A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress o, and maximum compressive stress o, if the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is I = 130 cm". Note: The uniform load represents the weight of the beam. [ Ans : G, = 105.8 MPa ; 6. = 28.8 MPa ]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Pravinbhai
In the case of loading in the figure below, by drawing the N-V-M-Ɵ-y diaphragms, sınce the equilateral steel beam AB has a triangular cross-section and the side length is 40mm, calculate the maximum and minimum normal stress to occur in the beam F1 =400N
I hope the tutor will give a detailed and clear answer
(1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force as shown. The modulus of elasticity for steel is 30 million psi and Poisson's ratio is 0.28. The second area moment of triangular beam about is centroid is I= bh³/36 (b: width, h: height). Find the stress state at point M within the cross-section B. y X 4 ft 4 ft 200 lb N.A. Cross section M 2 in 1 in 1 in 1 in
A solid rectangular homogeneous section (total length = 7.2m) is simply supported, where b = 50 mm and d= 175 mm. A concentrated load F = 140 N acts at point C where L1 = 4.00 m L2 = 3.20 m. Calculate the maximum bending stress and give your answer in N/mm2 to 2 decimal places. *Assume the weight of the beam is negligible and zero. F A B L1 L2 d A B Answer:
A composite beam is made of two brass [E = 112 GPa] plates bonded to an aluminum [E = 64 GPa] bar, as shown. The beam is subjected to a bending moment of 2230 N-m acting about the z axis. Assume b=48 mm, dz=31 mm, d2=8 mm. Determine: (a) the maximum bending stresses opy,Ja! in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) dz Aluminum (1) Brass (2) dz b Answers: (a) Obr i MPa, oal = i MPa. (b) Obrj = MPa.
4. A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied. 200 mm 40 mm 100 mm H 20 mm
Substitute the value for s = 5 For the beam and loading shown. P = 20×S N, F = 10×S N, Q = 4×S N/m, (INA 10.6x10° m). %3D -6 Determine the following and showing your steps: (a) Find the centroid of the cross section. (b) Find the maximum tensile bending stress in the beam and its location from point A. (c) The shear stress at point H in the cross section. (At a distance of 4 m to left of support D). 12 inm 15mm- 150 mm 12 mm 20mm A в с B H -5m 5m--4m-l- -14m- - I00 mm %3D
AT-shape beam is a load-bearing structure. The top of the T-shape cross section serves as a flange or compression member in resisting compressive stresses. In a building construction, the T-Shape beam which made of an elastic perfectly plastic material was used and its dimension is shown in Figure 3.2. For the beam indicated, determine the fully plastic moment and shape factor of the beam if the value of E = 200 GPa and o, = 250 MPa. (Use moment inertia for the cross section, I = 2600 x 10° m*) 60 mm 20 mm 60 mm 20 mm Figure 3.2 Beam cross-section
A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 19 mm from the top of the of the beam on a section 1.8 m from A if P = 5328 N, W = 2450 N/m, a = 1.49 m, b = 2.38 m, c = 1.46 m, L = 80 mm and h = 232 mm. Round off the final answer to two decimal places. W P A h C →
q5