A beam with a half-circular cross-section with radius R = 1.7 in is subjected to a maximum positive bending moment of 25700 lb in about a horizontal axis. Determine the maximum tensile and compressive flexural stress in the beam. Denote a tensile stress with a positive number, and a compressive stress with a negative number. psi psi o max R o maxc

A beam with a half-circular cross-section with radius R = 1.7 in is subjected to a maximum positive bending moment of 25700 lb in about a horizontal axis. Determine the maximum tensile and compressive flexural stress in the beam. Denote a tensile stress with a positive number, and a compressive stress with a negative number. psi psi o max R o maxc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam shown is subjected to compressive force of C1/2 kN.m, and bending moment of C2 N.m, calculate the total stresses on both points A and B* Sigma A = Sigma B = C2=140 C1=90 Во 40mm 20mm
The Figure shows a loading set up similar to that of the 'Bending in Beams' laboratory experiment. E = 200 GNm"2 and I = 2 x 109 m“. The bending moment and the radius of curvature at any point in the beam between the support points B and C are respectively: 1 kN 1 kN B 0.125 m 1.25 m O a. (-)125 Nm, 1.2 m O b.(-)12.5 kNm, 2.8 m O C. (-)2.5 kNm, 2.4 m O d.(-)125 Nm, 3.2 m
The composite beam in Fig. a is made of wood and reinforced with a steel strap located on its bottom side. If the beam is subjected to a bending moment of M = 2 kN # m, determine the normal stress at points B and C. Take Ew = 12 GPa and Est = 200 GPa.
1. Determine the moment M that should be applied to the beam in order to create a compressive stress at point D of op=30 MPa. Also sketch the stress distribution acting over the cross section and compute the maximum stress developed in the beam. A 25 mm M 150 mm `B - 25 mm 150 mm 25 mm 25 mm
2. A 0.5-m long circular cross-sectioned cantilever beam with radius r made of aluminum with E = 70.0 GPa and 120.0 MPa. An upward load F is applied at length 0.35 m from the fixed end. Determine the radius r Oallow so that the free end of the beam can bend upward at least 3.0 cm without failing. 3.0 сm 0.35 m Р
If the simply supported beam is subjected to the load shown below, determine the following: c- c - The internal bending moment acting on the cross-section through point C. d- d- The shear stress at section C.
The aluminum strut has a cross-sectional area in the form of a cross. It is subjected tothe Moment M = 8 KN.m. (i) Determine the bending stress acting at points A and B; (ii)Determine the maximum bending stress in the beam and sketch a three dimensional view of thestress distribution acting over the entire cross-sectional area.
Calculate the maximum normal and shear stress values for the attached beam at x = 8.5 m. Determine the distribution of the shear stress in the cross-section in the y-axis direction at y=55 mm, y=109.99 mm and y=110.01 from top. The dimensions of the beam are a = 5.5 m, b = 3.0 m and c = 2.5 m, and the cross-sectional dimensions are d = 170 mm and h = 130 mm. The distributed load of the beam has the value q = 3kN / m and the force F = 10kN.
Construct the shear-force and bending-moment diagrams and identify the largest negative bending moment. Assume a-3.9 ft, b =7.8 ft, c-3.9 ft. w-1100 lb/ft, and P-3200 lb. A Answer: Mmin a W B b P TTV C lb-ft D
From the given figure below, determine the flexural stress of the beam at fixed end if it has a cross section of 150mm wide by 250mm deep. HA VA 0 1750 40 N/m 3m -420Nm B & Im 550 35 N -75Nm с + 0° 55'N 20N 20N 0° DAV-DIAG -20Nm M-DIAG
A composite beam is made of two brass [E = 95 GPa] plates bonded to an aluminum [E = 74 GPa] bar, as shown. The beam is subjected to a bending moment of 1715 N-m acting about the z axis. If the moment of inertia about the z axis of the equivalent all-aluminum beam is 636712 mm4, find the maximum bending stress in the aluminum plate. Brass Aluminum Brass O 29.5 MPa O 36.6 MPa O 46.6 MPa O 40.4 MPa O 25.1 MPa 50 mm 10 mm 30 mm 10 mm
The beam consists of a W24 x 94 structural steel wide-flange shape [E = 29,000 ksi; I = 2,700 in.“). For the loading shown, determine: (a) the reactions at A and D (positive if the force is up, and the moment counterclockwise). (b) the magnitude of the maximum bending stress amax in the beam. Assume LAB = LBC =7 ft, LcD = 13 ft, w = 4.3 kips/ft, P = 41 kips. B D LAB LBC LCD Answers: (a) A = kips, D= i kips, Mp = kip-ft. (b) ơmax = ksi.