Figure 0) E 1.5 m D 1.5 m < 1 of 1 2 m P ▼ Part B Determine the vertical component of reaction at E. Express your answer to three significant figures and include the appropriate units. Ey = Submit - 5.2 μA Provide Feedback KN Previous Answers Request Answer ? X Incorrect; Try Again; 7 attempts remaining

Figure 0) E 1.5 m D 1.5 m < 1 of 1 2 m P ▼ Part B Determine the vertical component of reaction at E. Express your answer to three significant figures and include the appropriate units. Ey = Submit - 5.2 μA Provide Feedback KN Previous Answers Request Answer ? X Incorrect; Try Again; 7 attempts remaining

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Example 5.2: - Formation water sample with solids concentrations of calcium (Ca) = 460 ppm, sulfate (SO4) = 1,400 ppm, and Na plus Cl = 19,000 ppm. Find Equivalent NaCl solution in ppm.
Solve the value of Ely at the midspan. 6 kN 2 kN/m 4 kN 3 m 1.5 m 1.5 m- 348.75kNm^3 O-218.25KNM^3 O -281.25kNm^3 O-362.25kNm^3
A A A) RA= 1m B) RA= 1 50 KN 45 KN/m 1.5m 40 KN/m 6.00 m KN, RB = 3.00 m KN, RB = RB 275 KN 1 m 4.00 m KN 1.5 m KN/m B 250 KN 1.50 m
If there are 4 levels, m1 = 102.32 ton, m2 = 23.72 ton, m3 = 9.63 ton, m4 = 4.42 tonk1 = 4.31 kN/m, k2 = 19.7 kN/m, k3 = 30.19 kN/m, k4 = 36.44 kN/ma1 = 1 1. Determine the three modal frequencies and periods2. Determine the normalized mode shape factors3. Draw the mode shapes4. Determine the participation factors reference: pictures attached
With the soil profile as shown below, if the water table gradually drops to elevation (E) = -6 m, then the settlement is GWT G.L. El =0 Ya- 19.43 kN/m Yary- 17.53 kN/m Sand El = -10 m my- 0.02 cm/kg cy-0.20 cm/min Y 19.62 kN/m Clay El = -16 m Sand El=-20 m Rock (a) 5.80 cm (c) 2.40 cm (b) 4.20 cm (d) 6.10 cm
8. Estimate the settlement of the center of the tank, shown in the sketch, due to consolidation of the 20-ft layer of clay. 80'diam. -Oil tank; 500 lb/sq ft 30' fine sand; 125 lb/cu ft 20'clay; qu = 1.3 tons/sq ft W = 54 % Wp = 26% W = 44% Isat = /15 lb /cu ft %3D Rock %3D %3D
100 KN 150 KN 4.00 meters 5.00 m 4.00 meters 2.00 meters 2.00 meters Joint Horizontal Component Vertical Component A E Member Magnitude ВС BD
Research about the background study of DIRECT SHEAR TEST FOR SOIL and discuss.
43.8 kN/m RA= Bx= -3 m kN kN 29.2 kN/m 6 m By = B -3 m 133.5 kN 1814 KN 81.4 kN m
2. Consider a rectangular footing 3.2 m x 4.5 m to be constructed in a uniform clayey sand to support allowable loads as shown in Figure Q2. Assuming general shear failure would take place, determine the safety factor against bearing capacity failure when the ground water table is at 1.0 m above the ground surface. Comment on the obtained result.
Q6 Please provide justified answer asap to get a upvote
1.. How does the design of the apparatus enable the resultant-force on the- vertical surface to be measured? Are any significant forces be neglected? 2- Compare the theoretical and experimental values of (Wexpe) & (Wheo. ).Discuss any discrepancy? 3- What is the primary trend in yep-Yeg versus with water depth?