Fig. 4 illustrates an insulating wall of three homogeneous layers with conductivities k1, k2, and k3 in intimate contact. Under steady state conditions, both right and left surfaces are exposed to a temperature in a steady state condition at ambient temperatures of T and T , respectively, while ß, and BLare the film coefficients respectively. Assume that there is no internal heat generation and that the heat flow is one-dimensional (dT/dy = 0). For the illustrated ambient temperature in Fig. 4, determine the temperature's distribution at each layer. Material 3 Material 1 Material 2 T= 100 T= 35 °C Kı=20 K3=50 (W/m.k) K3=30 (W/m.k) B1= 10 w/m² °K (W/m.k) BR= 15 w/m²°K 50 mm 35 mm 25 cm Fig. 4

Fig. 4 illustrates an insulating wall of three homogeneous layers with conductivities k1, k2, and k3 in intimate contact. Under steady state conditions, both right and left surfaces are exposed to a temperature in a steady state condition at ambient temperatures of T and T , respectively, while ß, and BLare the film coefficients respectively. Assume that there is no internal heat generation and that the heat flow is one-dimensional (dT/dy = 0). For the illustrated ambient temperature in Fig. 4, determine the temperature's distribution at each layer. Material 3 Material 1 Material 2 T= 100 T= 35 °C Kı=20 K3=50 (W/m.k) K3=30 (W/m.k) B1= 10 w/m² °K (W/m.k) BR= 15 w/m²°K 50 mm 35 mm 25 cm Fig. 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A wall without heat generation is 0.5 m thick and is maintained on one side at T = 30°C, while the…

A: Data given- t= 0.5 m T1= 30°C q= 1200 W/m2

Q: Consider a 1m long, 3.5mm diameter wire, with a thermal conductivity of 20 W/mK. If the wire has a…

A: Given data: ◆ The length and diameter of the wire: L = 1 m , d = 3.5 mm = 0.0035 m ◆ The thermal…

Q: • Derive an expression for the temperature distribution within a sphere that has inner radius r,…

A: To derive an expression for the temperature distribution within a sphere.

Q: Assume steady-state, one-dimensional heat conductionthrough the symmetric shape shown in Figure…

A: Heat transfer: The transfer of heat from one body to another due to the temperature difference…

Q: An insulation layer of 20 mm thick refractory material is placed on top of a layer of mineral wool…

Q: 1. A simple cavity wall consists of two brick layers separated by an air gap of 50 mm. If the inside…

Q: A very long, rectangular cross-section block is made from metal with the following properties:…

A: Given Data: Thermal Conductivity k = 130 W/mK Density ρ=2771 kg/m3 Specific heat cp=703 J/kgK…

Q: An annulus (e.g., a tube) has a temperature of Ti at the inner surface (at ri) and a temperature of…

Q: the combined one-dimensional heat conduction equation. Show step-by-step solution and schematic

Q: Pls handwrite

Q: A spherical metal ball of radius r0 (r initial) is completely heated in a furnace to the temperature…

Q: ugh brick] tot pi 2.10 Compute Q and U for Example 2.11 if the wall is 0.3 m thick. Five (each) pine…

Q: An electrical resistance wire made of tungsten dissipates heat to the surroundings at a constant…

A: Given condition:- electrical resistance wire made of tungsten means heat generation, Temperature is…

Q: (a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under…

Q: The steady state temperature3/3 distribution in a one dimensional wall of thermal conductivity…

A: Write the expression of temperature distribution of one dimensional wall. T=a+bx2 Write the…

Q: It is observed that the temperature distribution, in steady-state, inside a one-dimensional wall…

Q: derive an expression for the thermal conductivity k(x) for these conditions

A: Given: q= 6000 W A(x)=1-x T(x)=300(1-2x-x3) x=0 , 1 To determine: Expression of thermal conductivity

Q: Steel pipe 1 cm thick, 1.0 m long and 8 cm deep, quiet with 4 cm thick insulation. The inner wall…

A: Given data: For steel pipe, outer diameter, do=8 cm ⇒Outer radius, ro=4 cm. Thickness of steel pipe…

Q: 80. A plate-type fuel element, having a thermal conductivity of 2 W/m-K, pro- duces heat. The heat…

A: The actual mechanism of heat transfer in any fin is first heat get conducted into the fin at its…

Q: 2-The steady-state temperature distribution in a one-dimensional wall of thermal conductivity…

Q: Using the general conduction equation for a Cartesian system, derive the expressions for the…

Q: There is a long cylinder inside an oven and we are using lumped capacitance method to find the…

A: Lumped capacitance method - In this method, the thermal system is reduced to a number of discrete…

Q: Steel pipe 3 cm thick, 1.0 m long and 10 cm deep, quiet with 6 cm thick insulation. The inner wall…

Q: A solid cylinder of radius R and length L is made from material with thermal conductivity 2. Heat is…

A: The heat transfer rate along the axis negligible. Thus, the heat transfer is along radial direction…

Q: A house has well-insulated walls 18.0 cm thick (assume conductivity of air) and area 450 m², a roof…

Q: Derive a heat rate expression for the following geometry. Assume there is a poor contact at the…

A: Consider the diagram shown below for the given system.

Q: A hollow infinite cylinder has internal radius 0.5 and exterior radius 2.0. The external surface is…

A: Internal radius of hollow infinite cylinder= 0.5Exterior radius of hollow infinite cylinder=…

Q: ir flow rate Water evaporation rate Makeup water rate Part B) ump power m a,o me mm Wp kg/s kg/s…

A: To determine the rate of air flow, evaporation and make up water and pump power

Q: (a) Estimate the thermal conductivity of the wall. The second situation involves the same planar…

A: The temperature at x=0.5 in is 96.5°F. The temperature at x=1.5 in is 91.5°F. The temperature Tf1…

Q: 4x

Q: In a heat transfer equipment in a laboratory you used a pipe of outside diameter 9cm to convey steam…

A: Given : d = 9 cm t = 3 cm k1 = 4 k2

Q: Find the interface temperatures of the layers,ASAP

A: Given, For the composite wall; l=4m b=3m h=3mwhere, area of rectangular wall…

Q: A composite wall is formed by sandwiching a 0.1 m thickness material between two steel slabs. The…

Q: Consider a solid sphere of radius R with a fixed surface temperature, IR. Heat is generated within…

A: The heat generated is given by q=20+10r W/m3. The radius of the sphere is R=3 m. The thermal…

Q: A hollow cylinder has length L, inner radius R, and thickness d, and the temperatures at the inner…

A: To determine: Relation for radial heat conduction through a hollow cylinder

Q: Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure…

Q: Fluid at constant temperature T, with convective heat transfer of h, flows inside the composite…

A: The thermal resistance between the fluid and the inner layer of the pipe is The thermal resistance…

Q: Derive an expression for heat conduction through a composite plane wall of n- layers.

Q: What is the analogical reason between heat transfer by conduction and flow of electricity through…

Q: 1. The two faces of a thin metal sheet that is 3 units wide and 5 units long are insulated, and the…

A: Two faces of thin metal sheet is insulated.Length of the plateWidth of the plateThe temperature of…

Q: A slender rod of length L, diameter d (L >> d) and thermal conductivity k1 is joined with another…

A: Given:one Slender rod of length L and thermal conductivity k1Second slender rod of length L and…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Fig. 4 illustrates an insulating wall of three homogeneous layers with conductivities k1, k2, and k3 in
intimate contact. Under steady state conditions, both right and left surfaces are exposed to a temperature
in a steady state condition at ambient temperatures of T and T , respectively, while ß, and BLare the
film coefficients respectively. Assume that there is no internal heat generation and that the heat flow is
one-dimensional (dT/dy = 0). For the illustrated ambient temperature in Fig. 4, determine the
temperature's distribution at each layer.
Material 3
Material 1
Material 2
T= 100
T= 35 °C
Kı=20
K3=50 (W/m.k)
K3=30 (W/m.k)
B1= 10 w/m² °K
(W/m.k) BR= 15 w/m²°K
50 mm
35 mm
25 cm
Fig. 4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In this question, we are concerned with the evolution of the temperature u(x, t) in a homogeneous thin heat conducting rod of length L = 1. We can consider that the rod is laterally insulated as to have a one-dimensional problem. The evolution of the temperature is governed by the one-dimensional heat equation ди 0 0 = K Ət Əx2' Assume that this equation is subject to the following initial conditions u(x,0) = f(x) and boundary conditions (0, t) = 0 and ди (1,t) + и(1,t) — 0 (i) Discuss briefly the physical meaning of the boundary conditions.
Three of the following statements are true, but one is false. Indicate which one is false. O Insulation my increase or decrease the heat transfer from a pipe or a sphere. O There is no critical thickness of insulation for a flat surface (plane wall). O Small bodies with high thermal conductivities and low convection coefficients are less likely to satisfy the criterion for lumped system analysis. In a cylindrical pipe or a spherical shell, the additional insulation increases the conduction resistance of the insulation layer but decreases the convection resistance of the surface.
Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure 1.Assuming that there is no internal heat generation, derive an expression for the thermal conductivity k(x) for these conditions: A(x) = (1 -x), T(x) = 300(1 - 2x -3x),and q = 6000 W, where A is in square meters, T in Kelvin’s, and x in meters. Consider x= 0 and 1.
Example 2.10 Consider a 25 mm x 25 mm x 1 mm thick silicon die attached to a same size 2 mm-thick copper cap through a 0.1 mm thick thermal interface material (TIM) as shown in Figure 2.1. Convection heat transfer coefficient on the top side of the copper cap is 2500 W/m²°C. If thermal conductivity of silicon, copper, and thermal interface material are 125, 390, and 5 W/m°C, respectively, what is the total thermal resistance from the active (bottom) side of the silicon die to outside ambient?
The steady-state temperature distribution in a one-dimensional wall of thermal conductivity 50 W/m -K and thickness 50 mm is observed to be T(°C) = a + bx, where a = 200 °C, b=-2000 °C/m², and x is in meters. i. ii. What is the heat generation rate in the wall? (8) Determine the heat fluxes at the two wall faces. In what manner are these heat fluxes related to the heat generation rate? (
Consider the square channel shown in the sketch operating under steady state condition. The inner surface of the channel is at a uniform temperature of 600 K and the outer surface is at a uniform temperature of 300 K. From a symmetrical elemental of the channel, a two-dimensional grid has been constructed as in the right figure below. The points are spaced by equal distance. Tout = 300 K k = 1 W/m-K T = 600 K (a) The heat transfer from inside to outside is only by conduction across the channel wall. Beginning with properly defined control volumes, derive the finite difference equations for locations 123. You can also use (n, m) to represent row and column. For example, location Dis (3, 3), location is (3,1), and location 3 is (3,5). (hint: I have already put a control volume around this locations with dashed boarder.) (b) Please use excel to construct the tables of temperatures and finite difference. Solve for the temperatures of each locations. Print out the tables in the spread…
Derive a 2 dimensional transient heat conduction equation for a hot coffee in a mug. Assume that the coffee has a uniform temperature of 56 degree Celsius. Sketch the schematic diagram and propose your assumption for the derivation of the heat transfer equation.
any help would be much appreciated thanks
2. The slab shown is embedded in insulating materials on five sides, while the front face experiences convection off its face. Heat is generated inside the material by an exothermic reaction equal to 1.0 kW/m'. The thermal conductivity of the slab is 0.2 W/mk. a. Simplify the heat conduction equation and integrate the resulting ID steady form of to find the temperature distribution of the slab, T(x). b. Present the temperature of the front and back faces of the slab. n-20- 10 cm IT- 25°C) 100 cm 100 cm
A wall as given in fig is made up of two layers (A) and (B) The temperatures are as shown in the sketch. The ratio of thermal conductivities of two layers is given as KA = 3 the ratio t, : t, is KB T2 = 1200 T, = 1300° C B T3 = 30 A
(3) Determine the permissible value of electrical current flowing copper wire of d=2 mm diameter, covered with rubber insulation with a thickness of 8=1 mm, if it is known that the temperature of the insulation can not be larger than 333 K. The calculations assume: electrical resistance of copper wire R=5-103 Q/m, conductivity of the rubber 1=0,15 W/(m-K), of surroundings heat transfer coefficient a=8 W/(m²-K), at an ambient temperature of air t,=20°C.