consider steady state two-dimensional conduction in the plate shown in the Fig. below in which the four boundary conditions are nonhomogeneous, by applying The separation of variables method

Q: #21 jok 14k Rk 15k Find Re →7k

A: Write the algebraic sum of forces in x-direction. ∑Fx=15213+7cos10°+825-14cos23°-10-1235=-7.717 k

Q: In a vehicle when it is turned the axis of the wheel on the inside of curve turns through 45° angle…

A: Given data: -  The angle of the inside wheel is θ = 45o. The angle of outside wheel is φ = 30o. The…

Q: d the resultant and its orientation.

A: given

Q: 5 400 200 A 1 120° 4 200 (mm) 350 B 2.

A: The number of I centres are given as : N=n(n-1)2N= Number of I centersn = number of links for…

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: The isometric view is given in the above figure.We have to find out multiview of the given isometric…

Q: Direction. Draw the Force Sody Diagram of he tollowing iustrations. Lund

A: Draw the free body diagram for the given figures.

Q: v As a particle with a velocity in the negative x direction passes through the point (0, 0, 1), it…

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: v to find angle alpha??

A: To find angle alpha

Q: Problem 3. a. A force has a magnitude of 1 kN and coordinate direction angles of 0,= 60°, 8, = 120°,…

A:

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: Locate and draw the INSTANT CENTERS ( Known and unknown )

A: Locate and draw the INSTANT CENTERS ( Known and unknown )

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: If the resultant angle is known, then the formula to find the actual angle in a rotating system is O…

A: Let us discuss about formula to find resultant angle in rotating system.

Q: What is the parallel-axis theorem?

A: According to this theorem, moment of inertia of an object about any given axis is sum of moment of…

Q: Dimension this object.

A: Find Provide the dimension of the given project.

Q: Calculate the time to complete one circular motion.

A:

Q: Draw an isometric sketch of the object from the viewpoint W-Corner.

A: According to the details provided in the question, we need to calculate the isometric view.

Q: mechanism. You have a closed polygon, where: a = length of input crank = 1 inch b = length of…

A:

Q: Find the total force A

A: Given Data:   To Find: Magnitude of A.

Q: 3. The distance between end projectors of a line CD which is inclined 45° to VP, is 60 mm. Point C…

A: the distance between end projector of a line CD which is inclined 45 to VP , is 60mm . point C is…

Q: hank you, How do we know that the center of the Mohr's circle is located in the origin?

A: Given-T= 230 N-m;  yield strength in tension =160 MPa ,yield strength in tension =160 MPa ; yield…

Q: 1. Give the rectangular coordinates of the point C (p = 4.4, q = -115, z = 2). 2. Give the…

A:

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: Q1: Consider the points A, B, C, D where coordinates are respectively (1,1,0), (-1,1,0), 0,-1,1).…

A: According to the given  information solution is given below…

Q: For the stress states above determine the required yield strength of the material based on the…

A:

Q: show all steps in detail, units and formulas please.

A: Step 1:Step 2:Step 3:Step 4:

Q: 4- The equation ofthe plane which contains the points A (-1,0,1), B (1,-2, 1) and C(2. 0.-1) is

A:

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.