F7-20. If the bar assembly is made of a material having ayield stress of ry - 350 MPa, determine the minimumrequired dimensions h, and hz to the nearest mm. Apply afactor of safety FS. - 1.5 against yielding. Each bar has athickness of 12 mm.75 kN150 kNA 75 kN

The load in the bar AB is The load in the bar BC is

Answered: F7-20. If the bar assembly is made of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

600 lb 600 lb An aluminum rod to be used in an aircraft control system is required to stretch 0.12 in. when a 600-1b tensile load is applied to it. If E = 10.2 × 10³ ksi and the allowable stress is 17 ksi, determine the smallest diameter that can be selected for the rod and the corresponding required length of the rod.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
FBD 3. Determine the required thickness of member BC and the diameter of the pins at A and B if the failure normal stress for member BC is Ofail = 30 ksi, and the failure shear stress for the pins is Tfail = 12 ksi. Use a safety factor of 1.2 to your design. Solution: 1.5 in. 60° 8 ft 5 kip/ft
The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a = 290mm, b = 120mm, c = 80mm, and e = 35°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 36 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F2 Support bracket A a Answers: Tpin B = MPa Ob = i MPa
use this values lamp = 81 kg, AB = 5 mm, BC = 8mm

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

F7-20. If the bar assembly is made of a material having a yield stress of ry - 350 MPa, determine the minimum required dimensions h, and hz to the nearest mm. Apply a factor of safety FS. - 1.5 against yielding. Each bar has a thickness of 12 mm. 75 kN 150 kN A 75 kN