15:39Given-Assign..External Problem 1: Dimensional analysis and similarityA fighter aircraft is to operate at 200 m/s in air at standard conditions (p= 1.2 kg/m³). Amodel is constructed to 1/20 scale (length ratio) and tested in a wind tunnel at the sameair temperature (same air viscosity) to determine the drag force. The drag force Fp is afunction of the air density p and viscosity u, the velocity V and the cross section length ofthe airplane D.a) Use dimensional analysis to prove that:FpVD?and r, =pVDWhat are these two dimensionless numbers?b) If the model is tested at 50 m/s, what air density should be used in the windtunnel? Comment the result and give a recommendation.c) If the model drag force is 250 N at 50 m/s, what will be the drag force of theprototype?Lift force200 m/sDrag forceExternal Problem 2: Dimensional analysis and similarityThe viscous torque T produced on a disc rotating in a liquid depends upon thecharacteristic dimension D, the rotational speed N, the density pand the dynamicviscosity u

Given: Velocity of the prototype (Vp)=200m/sDensity of the fluid in prototype (ρp)=1.2kg/m3Scale…

External Problem 1: Dimensional analysis and similarity A fighter aireraft is to operate at 200 m/s in air at standard conditions (p= 1.2 kg/m³). A model is constructed to 1/20 scale (length ratio) and tested in a wind tunnel at the same air temperature (same air viscosity) to determine the drag force. The drag force Fp is a function of the air density p and viscosity 4, the velocity V and the cross section length of the airplane D. a) Use dimensional analysis to prove that: F and , = pVD What are these two dimensionless numbers? b) If the model is tested at 50 m/s, what air density should be used in the wind tunnel? Comment the result and give a recommendation. c) If the model drag force is 250 N at 50 m/s, what will be the drag force of the prototype? Lift force 200 m/s Drag force

External Problem 1: Dimensional analysis and similarity A fighter aireraft is to operate at 200 m/s in air at standard conditions (p= 1.2 kg/m³). A model is constructed to 1/20 scale (length ratio) and tested in a wind tunnel at the same air temperature (same air viscosity) to determine the drag force. The drag force Fp is a function of the air density p and viscosity 4, the velocity V and the cross section length of the airplane D. a) Use dimensional analysis to prove that: F and , = pVD What are these two dimensionless numbers? b) If the model is tested at 50 m/s, what air density should be used in the wind tunnel? Comment the result and give a recommendation. c) If the model drag force is 250 N at 50 m/s, what will be the drag force of the prototype? Lift force 200 m/s Drag force

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

c) The drag force Fp on a cylinder of diameter d and length / is to be studied. What functional form relates the dimensionless variables if a fluid with velocity V flows normal to the cylinder?
The aerodynamic drag of a new sports car is to be predicted at a speed of 60.0 mi/h at an air temperature of 25°C. Automotive engineers build a one-third scale model of the car to test in a wind tunnel. The temperature of the wind tunnel air is also 25°C. The drag force is measured with a drag balance, and the moving belt is used to simulate the moving ground (from the car’s frame of reference). Determine how fast the engineers should run the wind tunnel to achieve similarity between the model and the prototype.
5. The drag force, fd, on a sphere located in a pipe through which a fluid is flowing is to be determined experimentally. Assume that the drag is a function of the sphere diameter, d, the pipe diameter, D, the fluid velocity, V, and the fluid density, p. (a) What dimensionless parameters would you use for this prob- lem? (b) Some experiments using water indicate that for d = 0.2in., D = 0.5in, and V = 2ft/s, the drag is 1.5 x 10-3lb. Estimate the drag on a sphere located in a 2 - ft-diameter pipe through which water is flowing with a velocity of 6ft/s. The sphere diameter is such that geometric similarity is maintained. (Ans: 31.11b) Sphere
5. Use dimensional analysis to estimate quantities. Consider a gas with density p, pressure p, and ratio of specific heats y. The speed of sound, c, is an important parameter when considering high-speed gaseous flows where compressibility of the gas may be significant (planes, turbines, etc.). (a) Use dimensional analysis to derive a formula for the speed of sound, c = f(y, p,p). (Recall that dimensional analysis can't give you the *exact* relationship between dimensionless groups, so you might need to guess how c varies with y.) (b) Look up the density of air at 25° C at ambient pressure. Assume you don't know y- let's say y = 1 as a guess. Use your formula to estimate what c is, in meters per second. How close (or far) is your estimate from the experimentally determined value (346.1 m/s), in terms of % error? (c) Use your formula from part (a) to determine the ratio of the speed of sound through helium compared to air. Why do people sound funny after they breathe in helium?
The drag force on a truck moving at a speed of 95 km/h is to be estimated using the measured data of a similar 1:10 scale model tested in a wind tunnel, Standard air is the fluid in both the prototype and the model, The truck frontal area is 10.7 m and the measured drag force on the model is 3000 N. Determine: a) the air velocity used in the wind tunnel model tests, and b) the prototype drag force in terms of the measured model drag force.
The drag FD of the golf ball is affected by the speed V of the ball, the diameter d of the ball, the depth , of the dimple, the radius r of the dimple, the density C of the dimple, the density of air, and the viscosity µ. Perform a dimensional analysis to represent the drag of the golf ball as a function of these variables.
Acording to Darcy law, P is a pressure, V is a velocity, D is a diameter, g is acceleration gravity, f is dimensionless coefficient. Is the equation dimensionaly consistent?
Derive two dimensionless parameters for the shear stress at the pipe wall when an incompressible fluid flows through a pipe under pressure. In the dimensional analysis, use the following significant parameters: pipe diameter, flow velocity, viscosity of the fluid and density of the fluid. Solve the problem on white A4 size paper. Show all the calculation steps.
Hi asapppp
A wave-energy harvester is to be built off the north shore of Honolulu (seawater at 20°C) where the average wave speed is V = 15 m/s. The size of the prototype device is characterized by its height H Laboratory water tank (fresh water at 20°C) where the wave speed is 5 m/s (shallow water wave speed is only a function of depth). 6 m. A model is to be tested in the Davidson (a) express the predicted power generated W as a function of density p, height H, wave speed V, and gravity g. (b) similarity. (c) output. Derive a set of dimensionless parameters using the Pi theorm that will Determine the height of the laboratory model device to ensure dynamic If the model produces 6.85 kW, determine the expected prototype power
I need answer in 20 to 25 min asap and please dont give handwritten solution
The pressure drop AP in flow through pipes per unit length is found to depend on the average velocity u, diameter d, density of the fluid p, and viscosity u. Using MLT set of dimensions evaluate the dimensionless parameters correlating this phenomenon.