The pressure drop AP in flow through pipes per unit length is found to depend on the average velocity u, diameter d, density of the fluid p, and viscosity u. Using MLT set of dimensions evaluate the dimensionless parameters correlating this phenomenon. *

The pressure drop AP in flow through pipes per unit length is found to depend on the average velocity u, diameter d, density of the fluid p, and viscosity u. Using MLT set of dimensions evaluate the dimensionless parameters correlating this phenomenon. *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 5 s): The discharge pressure (P) of a screw pump (Fig. 5) is a function of flow rate (Q), screw diameter (D), fluid viscosity (u) and screw angular speed (w). P = f (Q, D, μ, w). Use the pi theorem to rewrite this function in terms of dimensionless parameters, ₁ g (T₂). Choose Q, D, and u as repeating variables. Screw Fig. 5: Screw pump
velocity (V), as well as the ball diameter (d) and its angular speed (). It is assumed that the he drag force Fp acting on a baseball is a finstion ofc the air density (p), viscosity (µ) and ball spins about an axis which is fixed with respect to the ground. Determine the similarity (Pi) groups and their functional dependence. Select p, V and d as "repeating variables".
Write the primary dimensions of each of the following variables, showing all your work: (a) specific heat at constant pressure cp; (b) specific weight; (c) specific enthalpy h. and (d) specific gas constant
A football, meant to be thrown at 60 mi/h in sea-level air( ρ = 1.22 kg/m 3 , μ = 1.78 E-5 N . m 2 ), is to be testedusing a one-quarter scale model in a water tunnel ( ρ =998 kg/m 3 , μ = 0.0010 N . s/m 2 ). For dynamic similarity,what is the ratio of prototype force to model force?( a ) 3.86 : 1, ( b ) 16 : 1, ( c ) 32 : 1, ( d ) 56 : 1, ( e ) 64 : 1
The lift of a wing, Fitift, is a function of wingspan, W, chord length, H, surrounding air density, p, and viscosity, u, and velocity, V. Using p, V, and W as repeating variables, express this relationship in dimensionless form.
c) When small aerosol particles move through air or water, the Reynolds number is very small (Re < 1). Such flows are called creeping flow. The aerodynamic drag on an object in creeping flow is a function only of its speed, V some characteristic length scale, L of the object and fluid viscosity, µas indicated in Figure 11. Use dimensional analysis to generate a relationship for Fp as a function of the independent variables. The dimensions of Fp are MLT2. FD L Figure 11
Ius A fluid flow situation depends on the Nelocity (V), the density several lineor dimension, 4shi, h2.pressure drep (DO > gravity (9) , Viscosity , Susface tension ). and bulk mo dulus of elasticity k. Apply dimen sional analysis. to these variables td A s*
A dimensional analysis is performed on the drag on a boat. When the effects of viscosity can be neglected, the Euler number based on the drag D experienced by the boat is a function of a Froude number. The effects of the dimensions of the boat can be represented by its length I. The drag on a model of the model is measured as 0.35N. If the ratio of / for a full-scale model to the value of/ for the model is 46, calculate the expected drag on the full-scale boat. Your answer should be to the nearest kN. The properties of the water in the model test matches those for the full-scale boat.
Q.2. The force of impeller depends on the volumetric flowrate of fluid (Q) through the pipe of diameter (d) ,fluid density and viscosity , rotation of impeller (N). By using the dimensional analysis (Buckingham's Theorem), find the relation between the above parameters.
List and describe the three necessary conditions for complete similarity between a model and a prototype.
For the drag force of an Aerobee rocket, D=0.00056v (Ib], obtain a linear model near v = 800 ft/sec and find the velocity below 800 ft/sec that the model prediction error becomes greater than 2%. Enter an answer in a whole number in ft/sec.
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.