Example: A 1.0 kw heater is Constructed ofaglass plte with anelectrically condcting film which produčes' a Constant hentflux . The plate is 60x 60 cm and placed in an air sebeetotestream at 27c,d atm with Uo=5 m/s. Calculate theaverage temp. difference along the plate, and thedifference at the trailing edge.

Q=1 KwA=60×60 cm2T1=27 °CPatm= 1 atmU∞=5 msecFor air properties at 27° Cμ=1.849×10-5…

Example: A 1.0 kw heats is Constructed ofaglass Pate with an electrically condueting Ailm wkich produces' a Constant hent Flux • The plate is 60x 60 cm and placed in an air seteceom stream at 27c ,1 atm with Uo=5 m/s. Calculate the average temp. difference along the plate, and the difference at the trouiling edge .

Example: A 1.0 kw heats is Constructed ofaglass Pate with an electrically condueting Ailm wkich produces' a Constant hent Flux • The plate is 60x 60 cm and placed in an air seteceom stream at 27c ,1 atm with Uo=5 m/s. Calculate the average temp. difference along the plate, and the difference at the trouiling edge .

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

surface heater is (128 psia) chen [4] The pressune în a (230000I6/hr) o water enfers at (84-7F)- Drains in the amount of (57b00 Ib/hr) enter at (120f) · Caleulate the steam flow at cn TTD is (4F). enthalpy of (10g5.5 Bru) when the
Please hemp mr, i need full and fast solution. Please don't provide handwritten solution ...
Pls answer with complete solution.
Find the heat capacity of the hot and cold fluid.
You are designing a pin-style heatsink for forced cooling of an IC. A small fan blows RT air into the heatsink at about 2.3 ? ? . The aluminum pins are 2mm in diameter and have a constant surface temperature of 120°?. The heatsink is 100mm x 100mm and the pins have an inline arrangement with a transverse pitch of 4mm and a longitudinal pitch of 6mm. What is the total heat dissipation of this heatsink? The pins are 30mm high. Note RT=25 celsius
8-4 Derive the following equations: (aF 0 (a) F = U + T tio (b) Су (OA8) ) (reversible process); (c) H = G – TOT)ati ilidsse Ioadh 1ol jedb sbul - bod (d) C, = -7(). -T) (reversible process);
Compartnments A and B of the tern k Shown in the figure below are closed and filled with air end a liquid with el specific grauity equal to o.6. 3.5hpa(gauge) B Open to the et moshore 3.ocm air Liquid with e specific grauity =0.6 water mercary w th a specific grauity =13.6 O If the atumospheric press ure is lol kpa Cabr) and preffure gaugle reads 3.5trpa (gauge).determine the manometer reading, h.
Estimate the required maximum Boiler Water Concentration for a steam drum operating at 800 psia 0 1,344 ppm 01,450 ppm O 2,358 ppm O 2,458 ppm 1 4 8 10 Next
A 2 m wide, 3 m high, and 50 mm thick sheet of XPS insulation (M = 50 ng/Pa.s.m2), has a vapor pressure of 1500 Pa on one side, and 3500 Pa on the other. Calculate the vapor flow rate (Qv), vapor flux (qv), permeability, Rv value and the permeability (μ)
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.
ut the exit ee condJeYging nazZle The aid delocity was 237m15 find Mach nun JbeY a this seetion qnd The stasntion n Pressiete if staghation Temperatuye was 33c and Xhe back Prestate was lo5 K Pa ( Kz fol, R=2873/he
FROM BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD