Preblen-6 A porfect gas,fassuned do be qir) s usupplieto Nozzle at low Vebcty atatloopsia acavergthingNozzle at low Vabady at at foopsy and 5405. The Nozzle discharges to arheesphorie a fressure (14-7Psin) Asswnity rictimless actiabatie tlaw, and pass Hlowrate of Hlow of (1) ltse-calentatet- fol The Pressule in the exit plave in, Psig The velacity in the exit plane, in Puse O The cress Sectional-avegof the exit planein

Q: Magnetic cooling can attain a temperature of roughly 0.05 K. In this technique, a high magnetic…

A: solution provided in attachment

Q: resolve, incorreect solutions

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q:

A: from the given options, it seems option 1 is correct

Q: Define the term form factor?

A: Generally, the word Form factor is defined for the surface finish and tolerance provided over any…

Q: What is known as extensive quantities ?

A: Extensive properties are those properties that depend upon the mass of the system. The energy…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: Prove please!

A:

Q: All physical quantities involve a direction

A: Given Physical quantity To find Direction based physical quantity

Q: would it be possible to get a detailed explanation? thank you

A:

Q: Thank you

A: given : t = 6.07mm = 0.00607 m F = 38.9 KN = 38900 N τ = 54.4 MPa = 54.4 x 106 N/m2

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: Can you write the work out or make it more clear?

A: Ajajja

Q: can I have FBD for this?

A:

Q: Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula?…

A:

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: Given:The force applied by the hydraulic press, The diameter of the piston, The diameter of the rod,…

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: Define the Temperature Scales?

A:

Q: It causes resistance due to applied forces which is a result of restrain deformations   Shear Force…

A:

Q: How forces are transmitted?

A:

Q: Hi could you also please give the solution to d, e, f

A: As per the guidelines we are subjected to solve only 3 sub parts at a time. Please repost the same…

Q: So no answer and this used one of my questions?

A:

Q: Please elaborate it well, this is an indoor consideration when designing cryogenic plant. you can…

A: Obig

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: 1.Convert 21 inches of Hg (vacuum, gauge) to kPa (absolute)

A: Since you have posted a multiple independent question in a single question we will solve first…

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: "If we push the book on the table, it stops after sometime. Why?"

A: If we push the book on the table, then the book will get some speed. but after some time the book…

Q: Texts: A haulage gear is driven by a motor which develops 15 kW at a full speed of 750 rev/min. The…

A: Step 1: Step 2: Step 3: Step 4:

Q: It is a water pressure copper pipe, household tap water coming out. Identify a copper pipe material…

A: Material: Copper (Specifically, type L copper)Justification: Type L copper is commonly used for…

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: give a steps by steps explanation of the solution

A:

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: In a three-phase separator, gas, oil, and water are separated into layers of different depths. The…

A:

Q: ACCURATELY

A: We have given ACCURATELY

Q: A manufacturing company has an order for a specific new product. The order quantity is 45,000 units.…

A:

Q: Problem 3: A small gearing system in your brand-new 3D printer fails as you were printing, leading…

A: To prove: We must demonstrate that the equipment failed under normal operating circumstances in…

Q: horwalizing 1) Machinability of low carbon steels improved by: high carbon steel improved by…

A: Heat treatment processes are used to get the desired properties in the metals.

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: A rigid tank (a closed system with fixed boundaries) with a volume of 0.45677 m³ contains 10 kg of…

A: Volume of tank, V=0.45677 m3Mass of refrigerant, m=10 kgPressure of vapor (refrigerant) P1=600 kPa,…

Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…

A: I will select second one i.e  spiral bevel gear. Alloys used in making gears is zinc alloys  or…