1. A fire has a total heat release rate of 4000 kW and is located at the center of the atrium floor. The smoke layer interface is 8 m above the floor. Determine the mass and volumetric rates of smoke being supplied by the plume to the smoke layer (i.e., at the location of the smoke layer interface).

1. A fire has a total heat release rate of 4000 kW and is located at the center of the atrium floor. The smoke layer interface is 8 m above the floor. Determine the mass and volumetric rates of smoke being supplied by the plume to the smoke layer (i.e., at the location of the smoke layer interface).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose that a company that works in extruding aluminium products has spent L.E. 50,000 on maintenance materials, L.E. 10,000 on maintenance labour, L.E. 250,000 on manufacturing; in order to produce 10,000 tons of extruded aluminium sections. If the total man-hours worked is 1,000 man-hour, the total cost of investment in the plant and equipment is L.E. 5E06, and the preventive and breakdown maintenance costs are L.E. 40,000 and L.E. 20,000, respectively, find the following: a) The ratio of maintenance labour cost to material cost. b) The ratio of total maintenance cost to total output. c) The ratio of total maintenance cost to total manufacturing cost. d) The ratio of total maintenance cost to total man-hours worked. e) The ratio of total maintenance cost to value of facility. f) The ratio of total preventive maintenance cost to total breakdown cost.
I need the answer as soon as possible
ESSE metal forming condition. 5) One of the common methods to reduce spring back in bending process is by- 4) Residual stresses (internal stresses) is found in
4. For the composite product shown (carbon fiber-epoxy duct flange), describe the plan to produce the final product from a complete product design (supplied by the customer's engineering department). You are responsible for all aspects of production; nothing is supplied other than the design. Explain/list all material, equipment, tooling & personnel requirements to be able to deliver a product of acceptable quality at a rate of 20 units per week. A contract has been signed for 2 years. For the sake of this part, assume there are no certifications required. Overall part size is 6.00" x 8.00" x 1.25" deep. Thickness is approx. 0.085" as produced by 8 plies of twill fabric. The surface shown is the visible side and requires a tooled surface. You choose the process.
sunt ple answ List (1) 1. grinding process: 2. spot welding: 3. drawing: 4. runner: 5. wavy edges: 6. hot forming: (choose List (II) a) a cross section of bar is reduced by pulling force. b) get bad dimensional accuracy of products. c) a process that involves the use of heat and pressure. d) strip's edges elongate more than the center. e) channel carry molten metal from spure to mold cavity. f) it has wheel consists of a large number of abrasive particles, called grains.
The mechanism of material removal in EDM process is: A) Erosion and Cavitations B) Cavitations and Evaporation C) Melting and Evaporation D) Melting and Corrosion
Please don't provide handwritten solution .....
The product shown in Figure 5 is to be machined using a non-conventional machining process. The material of this product is Silicon Nitride that can withstand a temperature up to 450 °C. i. Propose the appropriate process to produce the part. ii. Justify the mechanism of the process in (i). Figure 5: Pump impeller
The rope you are uncoiling is a right hand lay rope, state with reasons the direction of uncoiling.
calculate the probability of getting exactly 3 defective items in a batch of 10, where the probability of a defect is 0.2. explain
4. A manufacturing engineer would like to carry out an exercise to identify the source/s of the variations when measuring the length of plastic injection moulded part. a) Guide the engineer through the process which needs to be carried out. b) The preliminary findings obtained from the exercise are as follows: EV = 0.20, AV = 0.07, PV = 0.90. Complete the calculations to obtain the final results. c) What do the final results mean? d) How would the engineer know whether the produced parts are acceptable or not? e) What would you suggest to minimise the variations? solve part a b c in 30 mins i will give thumb up thanks
describe the sequences of five production steps and stages from the initial research and development idea to the launch of the product for a metal casing or a car engine block. Use descriptive diagrams and or images, data to support your answers.