For the composite product shown (carbon fiber-epoxy duct flange), describe the plan to produce the final product from a complete product design (supplied by the customer's engineering department). You are responsible for all aspects of production; nothing is supplied other than the design. Explain/list all material, equipment, tooling & personnel requirements to be able to deliver a product of acceptable quality at a rate of 20 units per week. A contract has been signed for 2 years. For the sake of this part, assume there are no certifications required. Overall part size is 6.00" x 8.00" x 1.25" deep. Thickness is approx. 0.085" as produced by 8 plies of twill fabric. The surface shown is the visible side and requires a tooled surface. You choose the process.

For the composite product shown (carbon fiber-epoxy duct flange), describe the plan to produce the final product from a complete product design (supplied by the customer's engineering department). You are responsible for all aspects of production; nothing is supplied other than the design. Explain/list all material, equipment, tooling & personnel requirements to be able to deliver a product of acceptable quality at a rate of 20 units per week. A contract has been signed for 2 years. For the sake of this part, assume there are no certifications required. Overall part size is 6.00" x 8.00" x 1.25" deep. Thickness is approx. 0.085" as produced by 8 plies of twill fabric. The surface shown is the visible side and requires a tooled surface. You choose the process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Your capstone design team is prototyping (e.g. you are building a model to test not a final product) a "fire identification drone. The final product is intended to fly over rugged wilderness areas and look for small fires that should be monitored and potentially fought or contained. It is NOT intended to be used in large active fires. Your subteam's job is to design and build the support frame for the drone (e.g. the structure where the motors, propellers, guidance electronics and GPS, heat sensors, radio receiver and transmitter, etc. are attached) for the prototype. You have access to a machine shop with saws, lathes (for removing material by rotating it and using a cutting tool), drills and a facility with 3-D printers that can print a variety of plastics using fused deposition modeling (this is the technique where a polymer filament is melted and forced through a nozzle to build a structure layer by layer). You will be testing in a summer/fall timeframe so you expect temperatures…
15.16. Files & More (F&M), a manufacturer of office equipment, is introducing a new product, the BUNGEE desk chair, made from elastic webbing that provides both comfort and support. The materials that go into the chair are shown below. a. Construct a product structure diagram that reflects how the product is assembled. b. Convert the product structure diagram into a multilevel indented bill of material. c. F&M is trying to decide how much of the chair to assemble for the customer prior to shipping. Recommend a preassembly strategy that would allow easy assembly for the customer, and document it with a revised multilevel indented bill of material.
As a technologist, you are given the following design task: In a manufacturing environment, the final product needs to be packaged and sealed. After the product is placed inside the plastic bag, a hot pressing die is to be used to seal the plastic bag by application of heat and pressure. The operation should be as follow: By pressing a pushbutton switch, the heating rail is advanced and the packaging material is heated along the adhesive strip. After the adhesion pressure has been reached, the heating rail must return to its start position The design specification includes the following: Pressure dependent reversal with monitoring of the end position by means of magnetic proximity switches. Include safety measures, a green light to show when the system is ready, a red light when system is in operation, a warning sound when the heating rail is moving. 1. Draw your pneumatic circuit design for this application. 2. Draw the electric circuit diagram for your design.
An automotive company has employed you as a manufacture engineer to start a new unit. You are assigned with the production of the crank shaft piston assembly as shown in FIGURE Q1a. As an engineer responsible for producing the components shown in FIGURE Q1b, you have been asked to prepare a report with following details. Select the appropriate materials for the components shown in FIGURE Q1b.Propose the manufacturing processes that can be used to manufacture each of the components Crankshaft, power gears shown in FIGURE Q1b(I). Discuss the selection of manufacturing process with reference to desired properties for connecting rod application. Recommend appropriate surface treatment methods for these parts as required by their application.
Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s') Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175
(a) Define Product Quaintly (Q) and Product Variety (P). Distinguish major types of Q and P. Illustrate the relationship between P and Q using a diagram. (b) Explain various layouts and their relationship to the low, medium, and high production quantities. Illustrate all layout types on a PQ diagram.
26)
Department of Mechanical Engineering PRINCIPLES OF COMPUTER AIDED ENGINEERING – MENG30 Please solve the problem by keupord 10.Consider the Material Selection Design Problem for the FRAME of a Human Powered Road Vehicle. Define the selection criteria, assign weights (importance), and evaluate the following alternatives based on COST, WEIGHT, STRENGTH, AVAILABILITY, MANUFACTURABILITY, ASSEMBLY, TEST & MAINTENANCE, ENVIRONMENT & SUSTAINABILITY, SAFETY & RELIABILITY: a.Steel b.Aluminum c. Titanium
Questions Three Consider the office chair design below, develop the design matrix and identify its type. Answer
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…
4. A manufacturing engineer would like to carry out an exercise to identify the source/s of the variations when measuring the length of plastic injection moulded part. a) Guide the engineer through the process which needs to be carried out. b) The preliminary findings obtained from the exercise are as follows: EV = 0.20, AV = 0.07, PV = 0.90. Complete the calculations to obtain the final results. c) What do the final results mean? d) How would the engineer know whether the produced parts are acceptable or not? e) What would you suggest to minimise the variations? solve part a b c in 30 mins i will give thumb up thanks
Kasapreku Distilleries Ghana Ltd, a liquor Production Company located in Ghana had a major contract to supply alcoholic beverage to a neighboring country within one week deadline. In the course of production, there was a major breakdown which led to a long downtime resulting in missing out on the deadline. Kasapreku had lost a great deal of money due to the company’s inability to seriously inculcate safety and maintenance engineering in their system. (a) Discuss the importance of safety in an engineering maintenance from Kasapreku’s case scenario