SchlumbergerGeneralEquivalent NaCl Salinity of SaltsGen-4(former Gen-8)GenLi (2.5)*2.0OH (5.5)*2.0E NH, (1.9)*Mg1.5KСаCO,Na and CI (1.0)1.01.0KMultiplierSO,СаCO,0.5 E NO, (0.55)"Br (0.44)*HCO,so,E I (0.28)*HCO,Mg-0.51020501002005001,000 2,0005,000 10,000 20,000 50,000 100,000300,000Total solids concentration (ppm or mg/kg)1 Multipliers that do not vary appreciably for low concentrations(less than about 10,000 ppm) are shown at the left margin of the chart© Schlumberger Example 5.2: - Formation water sample with solids concentrations of calcium(Ca) == 460 ppm, sulfate (SO4) = 1,400 ppm, and Na plus Cl = 19,000 ppm.%3DFind Equivalent NaCl solution in ppm.

The values and figure given in the question are as follows: The concentration of Ca=460 ppm The…

Answered: Example 5.2: - Formation water sample…

Example 5.2: - Formation water sample with solids concentrations of calcium (Ca) = 460 ppm, sulfate (SO4) = 1,400 ppm, and Na plus Cl = 19,000 ppm. Find Equivalent NaCl solution in ppm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For a sample of water with the ionic composition shown below, the Carbonate and Non-carbonate…

A: given- Concentration of the ions as shown in the table-

Q: Z=0 Water Table Steady State Recharge 4.1 m Ground Surface 0 z (meters) 11 K (meters/day) 0.5 K(z) =…

A: Given data:Hydraulic conductivity, k(z)=0.5+0.03zPorosity, n=0.23Depth of unconfined aquifer=-11mWe…

Q: b) From the following data calculate the carbonate bicarbonate and hydroxide alkalinities.…

A: Methyl orange alkalinity=total alkalinity p=phenolphthaleint=Methyl orange alkalinity

Q: (i) Calculate the Molarity, and mg/l as CACO3 for 200 mg/I H3PO4

Q: A given sludge with 98% moisture content is X times more bulky than with 95% moisture content. The…

A: "A given sludge with 98% moisture content is X times more bulky than with 95% moisture content."The…

Q: 1 The lower the water turbidity, the higher the allowable scour velocity in sedimentation tank.( ) 2…

A: 1 True - Lower water turbidity allows for higher allowable scour velocity as the particles in the…

Q: Water containing 50 mg/L of monodisperse (uniformly sized) spherical particles of diameter 100 μm…

Q: 6. The pH of the water is measured as 9.3 and the total concentration of carbonate species is found…

Q: A water contains 50.40 mg · L-1 as CaCO3 of carbon dioxide, 190.00 mg · L-1 as CacO3 of Ca2+ and…

Q: In a sludge digestion tank, if the moisture content of sludge is reduced from 90% to 80% then th…

Q: nal solid solu

A: solution of above problem is below:

Q: For a sample of water with the ionic composition shown below, the Carbonate and Non-carbonate…

Q: Q2: The initial pressure of a 200 ft thickness reservoir is 6000 psia, and the initial porosity is…

Q: Biochemical Oxygen Demand A water sample was incubated at 20 °C for 3 days and its BOD3…

A: Using formula to find ultimate BOD

Q: A river with 400 ppm of salt (a conservative substance) and a flow of 25.0 m3/s receives…

A: Given:- The concentration of salts in a river = (C1) = 400 ppm The flow rate of the river = (Q1) =…

Q: Fresh sludge has moisture content of 99% and, after thickening, its moisture content is reduced to…

A: Given that :- Fresh sludge has moisture content w1=99% After thickening moisture content = w2=96% To…

Q: er. the Darcy velocity in the aquifer is 0.025 f/da- tio is 0.334. the longitudinal dispersion…

A: given data contaminant mass of an aquifer =10 kg velocity =0.1 ft/day DL =0.01 ft2/day Dy =Dz…

Q: Estimate particle size of ilmenite (sg 2x sand =5.4) and anthracite (s.g. 2/3 of sand = 1.8) which…

A: Given data:Specific gravity of ilmenite = 5.4 Specific gravity of anthracite = 1.8 Specific gravity…

Q: For a sample of water with the ionic composition shown below, the Carbonate and Non-carbonate…

A: Equivalent weight=( total weight) / valency Eq wt of CaCO3 = 100/2 = 50mg/l To find carbonate…

Q: 8. A laboratory provides the following analysis obtained from a 50-ml sample of raw water: Ca - 60…

Q: In order to clarify water containing particles with a diameter of 120 µm, what is used is a settling…

Q: Q-3. Settling characteristics of a concentrated suspension~ C = 3000 mg/t were determined in a…

A: Initial concentration, Initial height, Thickened sludge concentration, Inflow rate, Height and time…

Q: Untreated water sample from the Kerian River, Parit Buntar has the following chemical composition: V…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: A large piece of dry rock as a mass of 2450 kg and volume of 0.925 m. The specific gravity of the…

A: Given data : Mass of dry rock (MDry)=2450 kgVolume of dry rock (VDry)=0.925 m3Specific gravity…

Q: A large cement kiln has a length of 125 m and a diameter of 3.5 m. Determine the change in length…

Q: If 100 mg of H,SO, (molecular weight 98 g/mole) is added to 1.021l of water, what is the final pH of…

A: Given data- 100 mg H2SO4Molar mass=98 g/mole1.02 l of waterTo Find-The final pH of solution

Q: 2. Refer to the constant head permeability test shown in the figure above. For a test, these values…

A: Calculate the hydraulic conductivity with the help of the following relation: k=QLA h tQ= volume of…

Q: If 19.3mL of the standardized Na2S2O3 solution was used in determining the DO, what is the DO…

A: 0.01 N Na2S2 O3 is used in titration to decolorized the blue solution and the volume of 0.01N Na2S2…

Q: lon concentrations obtained for a ground water sample (having pH = 8.1) are given below Ion Ca²+…

A: To Determine :- Carbonate hardness present in the given water sample.

Q: (d) Ca(HCO3)2 = 150 mg/L; Mg(HCO3)2 = 200 mg/L; CaSO4 = 180 mg/L; MgCl2 = 95 mg/L; CaCl2 = 137…

Q: A completely mixed activated sludge process operating at equilibrium is designed to treat 300 MLD of…

Q: (b) Yield of BOD analysis at 20°C with dilution factor, p=0.1 are as tabulated in Table Q2. Table Q2…

Q: 6. The result of a mechanical sieving are as follows. Mass Retained (grams) 4.50 12.50 Sieve size…

Q: concentration was found to be 150 mg/L. Given k20°c = 0.20/day (base e) and temperature coefficient…

A: Given data- BOD of 3 days at 20° C = 150 mg/L K 20° C = 0.20/day temperature coefficient for…

Q: Determine the liquid limit. Determine the plasticity index. Determine the liquidity index.

Q: 1. An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of the oil is 50 m. Find…

Q: 16. In performing water content determination, the readability of the balance for specimen greater…

A: Readability is the smallest division at which the scale or the balance can be read. It can be…

Q: A given sludge with 98% moisture content is X times more bulky than with 95% moisture content. The…

Q: One of the most challenging problems in environmental remediation is isolated blobs of contaminated…

A: Capillary rise is the movement of a fluid in a thin tube above the general level of the fluid, when…

Q: The quantity of water retained by the subsoil against gravity is known as:

A: Yield: it is defined as the amount of water that the soil can discharge for the plant used Porosity:…

Q: in water and explain how the two can be equal in a given sample of water.

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: Seri-1 well is drilled in the area of Seri Iskandar with several intervals as candidates of pay zone…

A: Porosity is a measure of the spaces between the material and a fraction of the volume of empty space…

Concept explainers

Laboratory Determination of Hydraulic Conductivity

Hydraulic conductivity is the measure of flowability of water inside the soil in the presence of a hydraulic gradient. The hydraulic gradient is defined as the difference in the water heads in the soil, which induces a water motion. In simple terms, a hydraulic gradient is the presence of a potential that induces a flow of water.

Question

100%

Schlumberger
General
Equivalent NaCl Salinity of Salts
Gen-4
(former Gen-8)
Gen
Li (2.5)*
2.0
OH (5.5)*
2.0
E NH, (1.9)*
Mg
1.5
K
Са
CO,
Na and CI (1.0)
1.0
1.0
K
Multiplier
SO,
Са
CO,
0.5 E NO, (0.55)"
Br (0.44)*
HCO,
so,
E I (0.28)*
HCO,
Mg
-0.5
10
20
50
100
200
500
1,000 2,000
5,000 10,000 20,000 50,000 100,000
300,000
Total solids concentration (ppm or mg/kg)
1 Multipliers that do not vary appreciably for low concentrations
(less than about 10,000 ppm) are shown at the left margin of the chart
© Schlumberger

Example 5.2: - Formation water sample with solids concentrations of calcium
(Ca) =
= 460 ppm, sulfate (SO4) = 1,400 ppm, and Na plus Cl = 19,000 ppm.
%3D
Find Equivalent NaCl solution in ppm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data:

VIEW

Calculating equivalent NaCl solution:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Laboratory determination of hydraulic conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two flow lines for seepage across an interface between two soil medium having different coefficient of permeability is as shown in the figure below. The entrance angle at the interface is 60° then: k, =1.0 x 10° m/s k -4 x 10 m/s (1) a (2) The exit angle az at interface is 67,55°, A Correct Option B The exit angle az at interface is 81.79, Correct Option The change in exit angle if 'k2' is reduced by 25% is 2.68°. D The change in exit angle if 'k2' is reduced by 25% is 1.78°.
How long would it take for chloride to be detected just outside the clay liner at the secondary MCL of 250mg/L? Assume diffusion is the only mechanism
Complete solution Civil engineering
Estimate the terminal settling velocity in water at a temperature of 15°C of spherical silicon particles with specific gravity 2.4 and average diameter of 0.05mm. Assume p=999 kg/m3 and p= 0.00113 Ns/m2
lon concentrations obtained for a ground water sample (having pH = 8.1) are given below Ca2+ Mg2+ Na+ HCO3- SO4²- CI- 2- Ion Ion concentration 100 6 (mg/L) Atomic weight Ca 40 Mg = 24 15 Na || 23 250 H= 1, C 16 12, 45 S = 32, O =16 39 CI= 35.5 Carbonate hardness (mg/L as CaCO3) present in the above water sample is
For quiescent conditions determine the settling velocity of spheres in water as a function of particle diameter. Assume the particle density is 1050 kg/m³ and use a particle diameter range of 0.01 to 10 mm.
Pls ans soon
1. The following information is provided for an activated sludge system design: Parameter Symbol Value Units Flow rate Q 10000 m³/d Influent BOD So 150 mg/L Effluent BOD S 2 mg/L Hydraulic residence time Ꮎ 4 hr Mean cell residence time Oc 6 d Maximum specific growth rate μm 3 1/d Half saturation constant Ks 40 mg/L Yield coefficient Y 0.5 Endogenous decay coefficient b 0.08 1/d Death rate coefficient γ 0.04 1/d Determine: a) The aeration tank biomass concentration (X) in mg/L b) The aeration tank oxygen requirement in kg/d c) The rate of biomass wasting in kg/d
Consider particles in suspension and their settling behaviour at different concentrations select the correct statement(s). Type 1 settling is called discrete settling. Your option is Correct B Terminal velocity in suspension is achieved when drag force is balanced by gravity force. Your answer is IN-CORRECT Correct Option 24 In Type 1 settling, for Ree(100, 300) Cn = Re 3 +0.34 (Re = Reynold's number) VRe D In Type 2 settling, the velocity of floc does not remain terminal and keeps changing as the size of the floc changes. Your option is Correct
v; == 01): (A): Explain the factors that the coefficient of permeability depend on. (B): Prove that: Vg = %3D
When a pressure of 2×10^4 kN/m² is applied to 50 litres of a liquid, its volume is decreased by 0.5 litre. The bulk modulus of liquid in N/m² is