Example 29.13 (a). Find the load and full-load speeds for a four-pole, 220-V, and 20-kW, shunt motor having the following data : Field-current = 5 amp, armature resistance = 0.04 ohm, Flux per pole = 0.04 Wb, number of armature-conductors = 160, Two-circuit wave-connection, full load current = 95 amp, No load current =9 A. Neglect armature reaction.

Example 29.13 (a). Find the load and full-load speeds for a four-pole, 220-V, and 20-kW, shunt motor having the following data : Field-current = 5 amp, armature resistance = 0.04 ohm, Flux per pole = 0.04 Wb, number of armature-conductors = 160, Two-circuit wave-connection, full load current = 95 amp, No load current =9 A. Neglect armature reaction.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

. A Short Shunt Compound DC Generator supplies 100-amp at 110-volt. Series field resistance of 0.04-ohm, armature resistance is 0.05-ohm, shunt field resistance of 57- ohm. Iron and friction losses mount to 852-watts. Find the power input and the over all efficiency.
Draw the circuit please.
I need the answer as soon as possible
hine. b) In rotating machines, how would the voltages be generated in windings or groups of coils? c) Sketch the Full-bridge driving circuit for the permanent magnet brushless (PMBL) DC motor. Q3/
A shunt-wound DC motor with the field coils and rotor connected in parallel (Figure 1) operates from a 130 V DC power line. The resistance of the field windings, R. is 208 n. The resistance of the rotor, R,, is 4.90 1. When the motor is running, the rotor develops an emf E. The motor draws a current of 4.46 A from the line. Friction losses amount to 45.0 W Part C Compute the emf E. • View Available Hint(s) Tematates Symbols undo redo Tese keyboard shortcuts Help V Submit Part D Compute the rate of development of thermal energy in the field windings. Express your answer in watts. > View Available Hint(s) Templates Symbols undo redo Teset keyboard shortcuts Help Pan,windings = Figure W K 1 of 1 Submit Part E Compute the rate Pin.rotor of development of thermal energy in the rotor. R ER, Express your answer in watts. > View Available Hint(s) Templates Symbols undo redo teset keyboard shortcuts help Pinrotor=
current - 1=?, and the power factor - cosp =?. 4. An out of balance three phase star connected load has the following complex currents: I₁ = lejº,A, I₂ =le¯6⁰,A and I₁=1e¹j6⁰, A. This load is supplied by a four wire power line from a balance voltage source. Find the r.m.s. value of the neutral current Io =? Wait to th
Q2. A 4-pole, 200 V, lap-connected shunt motor running at 1500 r.p.m. and draw currents of 50 from the mains. It has 500 conductors in it is amature slots. It has an amature and shunt field resistances of (0.05 ohm) and (200 ohm), (brush loss may be ignored). d) (e) commercial efficiency.
The current drawn by the 230 V DC motor of armature resistance 0.5 ohm and back emf 200 V is ?
Please answer only handwritten accepted...I will like that solution.. Please clear handwriting.. Please.. .
In order to get higher speed of Dc motor the ..... ....... voltage supply most be low back emf (Eb) most be high O frequency most be constant
A - Explain the symbols, operating principles and usage areas of the diodes given below. (Zener diode: photo diode: led diode: opto coupler) B- Draw the voltage trigger circuit and explain its operation. Explain how there is a difference between the voltage quadrant and the tripler
Under short circuit test, the short circuit voltage of transformer is O a. Equal to the rated voltage ОБ. O b. (3-5) % V rated O c. Maximum O d. Zero