Assume that a separately excited shunt de machine has a rated terminal voltage of 230 V and arated armature current of 100 A. Its armature winding resistance, commutating winding resis-tance, and compensating winding resistance are 0.08, 0.01, and 0.00842, respectively. The resis-tance of external wires (i.e., R…) is 0.00242. Determine the following:(a) The induced armature voltage if the machine is operating as a generator at full load(b) The induced armature voltage if the machine is operating as a motor at full load

We got an a separately excited shunt dc machine with, Terminal Voltage (Vt) = 230 V Armature current…

Assume that a separately excited shunt de machine has a rated terminal voltage of 230 V and a rated armature current of 100 A. Its armature winding resistance, commutating winding resis- tance, and compensating winding resistance are 0.08. 0.01, and 0.008 52, respectively. The resis- tance of external wires (i.e.. R.) is 0.0022. Determine the following: (a) The induced armature voltage if the machine is operating as a generator at full load (b) The induced armature voltage if the machine is operating as a motor at full load

Assume that a separately excited shunt de machine has a rated terminal voltage of 230 V and a rated armature current of 100 A. Its armature winding resistance, commutating winding resis- tance, and compensating winding resistance are 0.08. 0.01, and 0.008 52, respectively. The resis- tance of external wires (i.e.. R.) is 0.0022. Determine the following: (a) The induced armature voltage if the machine is operating as a generator at full load (b) The induced armature voltage if the machine is operating as a motor at full load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Shunt dc generator supplies 220 V at 90A .The resistance of Armature and shunt field winding are 0.04 and 110 ohm respectively.Assume the total brush drop is 2 V. Your answer the emf generated is. . O 215 V O 220 V 225 V O 230 V If An 4-pole lab wound dc generator has 120 slot at each 8 conductors per slot,flux is 0.03 Wb. the speed of dc machine is...
A direct current shunt dynamo continuously supplies an ohmic load of 50 Ohm at terminal voltage Vt= 1000 V. The armature winding resistance is 5 Ohm and the shunt pole winding resistance is 200 Ohm. The sum of mechanical losses is 400 W. What is the percent efficiency of the dynamo under these operating conditions? a) 70 b) 74 c) 87 d) 78 e) 85
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
32. An alternator requires an alternating current of 2.1 A to produce on short circuit its full-load current of 50 A. The same on open-circuit an emf of 320 V. The armature resistance is 1Ohms . Find the full-load percentage regulation with a lagging p.f. of 0.6 when terminal p.d. on load is 2000 V. A. 7.2% B. 28.8% C. 3.6% D. 14.4%
QUESTION 1 a) Write down three (3) factors that will determine the induced torque in a DC machine. b) Explain why higher voltage applied to a motor doesn't always mean that it will have a higher induced torque. You can give an example of the scenario to answer this question. c) When a motor is powered up and rotates, it will induce an internal generated voltage. Is this statement true or false? Justify your answer. d) For the core design shown in Fig. 1: i. Design the magnetic circuit model. Indicate clearly for each part that you use in the magnetic circuit which part of the core is represented. ii. Predict what will happen to the total reluctance if the depth is increased. Justify your answer. rl r2 r4 9 cm 9 cm -25 cm 15 cm to -25 cm- 9 cm 2 A 200 turns -0.04 cm 25 cm 9 ém
Please answer all subparts for like either dislike is ready..please both questions.. Please.
please include circuit design
In DC machines, ....................... are made from laminated steel or low carbon steel and used to reduce the armature reaction.
A single phase Half wave AC voltage controller has a resistive load of 16 ohms with input supply voltage of 240 V, 50 Hz. The delay angle of the thyristors is, a = 21/5. Determine a) The rms output voltage and current. b) Input power factor and Input current. c) Average output voltage and current.
Colve asap
Q3. Write if the shown statements are TRUE or FALSE. 1- In DC machine the induced e.m.f is proportional with flux only. 2- The Ta/l a graph of a d.c. series motor is a straight line throughout. 3- In a DC motor the direction of the shaft rotation can be change by changing the polarity of the power supply. 4-The critical resistance is less than armature resistance in shunt generator. 5-As the load is increased, the speed of a d.c. shunt motor increases slightly.