Answered: What are the advantages and…

Engineering

Electrical Engineering

What are the advantages and disadvantages of using Flyback and Push-Pull Converters in electrical power applications?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Related questions

Q: Explore the significance of power management and thermal considerations in microchip design and…

A: We have to explore the significance of power management and thermal considerations in microchip…

Q: Design a transformer-fed HWR that provides an output effective voltage of 60V. Use the ideal diode…

A: Design Hall wave rectifier. Average output voltage = 60V All diode are ideal state. Find turn…

Q: What are the key design considerations that need to be taken into account while designing a Flyback…

A: When designing a Flyback Converter or a Push-Pull Converter for a specific electrical power…

Q: Design a transformer-fed bridge type FWR to provide an output load voltage of 40VDC. Use th deal…

A: Design full wave rectifier. Average output voltage = 40V All diode are ideal state. Find turn…

Q: A 48kW, 600V, 1500 rpm separately excited de motor is controlled by single phase semi-controlled…

A: Armature resistance (Ra) = 1 Ω Field resistance (Rf) = 145 Ω Firing angle of…

Q: A de machine is controlled by the step-down de-de converter shown below. The armature inductance La…

A: The question is about buck converter circuit.

Q: Needs Complete solution with 100 % accuracy.

A: The objective of the question is to calculate the input power to a DC series motor powered by a…

Q: What are buck and boost converters and how are they used in power electronics?

A: Buck and boost converters are types of power electronics circuits that are used for voltage…

Q: Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately…

A: Given Vph=150 Vra=0.2 Ωkb=0.4N=750 rpmI0=40 A

Q: A single phase half controlled rectifier is used to control speed of a dc motor rated at…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: What are the differences between a Flyback Converter and a Push-Pull Converter in Electrical…

A: Both flyback and push-pull converters are commonly used in electrical engineering for power…

Q: The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a…

Question

What are the advantages and disadvantages of using Flyback and Push-Pull Converters in electrical
power applications?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction and Explanation:

VIEW

Step 2: Advantages and Disadvantages:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
I:01)
Two generators operating in parallel supply a total load current of 150 A.The terminal potential difference of one machine falls from 250 V on no-load to 234 V when its current output is 100 A. The terminal potentialdifference of the other machine falls from 250 V on no-load to 230 V when its armature current is 80 A. The external characteristics are rectilinear. Determine :(i) The current supplied by each machine; and (ii) Terminal voltage. A: 91.46 A, 58.54 A, 235.37 V
DA de machine is controlled by the step-down de-de converter shown below. The armature inductance La =0.2 mH and the armature resistance can be neglected. The armature current is 5A. The Buck converter is operating at the switching frequency is 30 kHz and the duty ratio is 0.8. + > ~ Answer the following questions: 1) Calculate the input voltage (Va) if the output voltage (ea = 200 V). 2) Find the ripple in the armature current (la). 3) Calculate the maximum and minimum values of the armature current (la). 4) Sketch the armature current (ia (t)) and the supply current (ig(t)).
A DC chopper is used in regenerative braking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continuous and ripple free. What is the value of power feedback to the supply ?
The winding of a 4-pole alternator having 36 slots and a coil span of 1 to 8 is short-pitched by ........... degrees. 150 40. 90 20 Brushless excitation system consisting of: Stator field winding and power diodes stator and rotor field winding and capacitor stator and rotor field winding and power diodes Everything mentioned in the options Full Name : *
Please try to solve
dc machines
The armature of a d.c. The machine has a resistance of 0.25 ohm and is connected to a 300V supply. Determine the e.m.f. generated when it runs as a generator giving 100 A and as a motor taking 80 A.
What Is CNC Machining? How does it work?
Needs Complete solution with 100 % accuracy.