Q 3. The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-downtransformer with turns ration10 : 1. The load resistance RL, is 10 N.Determine (a) the average output voltageVolav), (b) the average load current I(av), (c) the rms load voltage Volrms), (d)the rms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage Vr(rms), (g) theaverage diode current Ip(av), (h) the rms diode current Ip(rms), (i) the peak inverse voltage PIV of the diode, (j) theaverage output power Po(AC), (k) the DC output power Po(DC), and (I) the frequency fr of the output ripple voltage. (

Answered: Image /qna-images/answer/b4984062-02d4-4463-9581-cc0b70ed6aec.jpg

The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-down sformer with turns ratio n = 10 : 1. The load resistance RL is 10 N. ermine (a) the average output voltageVo(av), (b) the average load current Io(av), (c) the rms load voltage Vo(rms), ms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage V(rms), (g) the age diode current Ip(av), (h) the rms diode current ID(rms), (i) the peak inverse voltage PIV of the diode, (j) the age output power Po(AC), (k) the DC output power Po(DC), and (1) the frequency f, of the output ripple voltage. (d)

The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-down sformer with turns ratio n = 10 : 1. The load resistance RL is 10 N. ermine (a) the average output voltageVo(av), (b) the average load current Io(av), (c) the rms load voltage Vo(rms), ms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage V(rms), (g) the age diode current Ip(av), (h) the rms diode current ID(rms), (i) the peak inverse voltage PIV of the diode, (j) the age output power Po(AC), (k) the DC output power Po(DC), and (1) the frequency f, of the output ripple voltage. (d)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms and rectifier…

A: Given, AC input voltage, VRMS=10 V load resistor, RL=10 Ω Power losses in rectifier, PL=2 W

Q: The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at…

Q: A 60 Hz sinusoidal voltage with an RMS value of 240 V is applied to a single-phase half-wave SCR…

Q: A 60 Hz sinusoidal voltage with an RMS value of 240 V is applied to a single-phase full-wave SCR…

A: The problem is from power electronics subject. The solution is given below.

Q: Find VDc if VAN = VBN = VCN= 120 volts... Half-wave Three-phase Rectifier Conduction Waveform…

A: To convert the AC into DC, Rectifiers are used . It can be controlled as well as uncontrolled .diode…

Q: For the full wave rectifier circuit shown in Figure 1, calculate: 1) The maximum current through the…

Q: The input to a full-wave rectifier is 40 V AC (RMS). The load resistor is 10 ohms. The DC voltage at…

A: The input to a full-wave rectifier : V=40 V (rms)and Load resistance RL=10 ΩThen DC voltage at the…

Q: A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 2. The transformer…

A: A full wave rectifier that uses 2 diodes, Internal resistance of each diode r=20 ohm, RMS value of…

Q: 120 V rms a. b. 3:1 00000 reliee 叶 DI D₂ # What is the peak current through each diode? What is the…

Q: 2. Draw the circuit for a full-wave rectifier, with a center-tapped transformer. If the AC input is…

A: According to the question, for the center-tapped full wave rectifier, we need to find and draw the…

Q: Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode…

Q: The single-phase halt wave rectifier has a L = 6.5 mH, R = 0.5 Q. and E = 10 v." %3D imput voltage…

A: The answer as given below steps:

Q: A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74…

Q: The input voltage of a single-phase full- wave diode rectifier is v= 100 sinwt Volts and the…

A: The solution can be achieved as follows.

Q: A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 58…

A: The average dc output voltage of the full-wave SCR rectifier is given by the expression as shown…

Q: The power output of the half-wave rectifier is rated at 102.4 W with a load resistor of 40 ohms. The…

A: Given, P = 102.4 W R = 40 ohm

Q: The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms. The DC voltage at…

A: Given, input AC voltage, VRMS=10 V load resistor, RL=10 Ω

Q: A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR…

Question

Q 3. The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-down
transformer with turns ration
10 : 1. The load resistance RL, is 10 N.
Determine (a) the average output voltageVolav), (b) the average load current I(av), (c) the rms load voltage Volrms), (d)
the rms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage Vr(rms), (g) the
average diode current Ip(av), (h) the rms diode current Ip(rms), (i) the peak inverse voltage PIV of the diode, (j) the
average output power Po(AC), (k) the DC output power Po(DC), and (I) the frequency fr of the output ripple voltage. (

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
The power output of the half-wave rectifier is rated at 51.2 W with a load resistor of 20 ohms. The peak voltage at the output is: O A. 25 V O B. 203 V O C. None of the other choices are correct O D.51 V O E. 102.5 V
The power output of the half-wave rectifier is rated at 25.6 W with a load resistor of 10 ohms. The average voltage at the output is: O A. 32 V O B. None of the other choices are correct O C. 8 V O D. 16 V O E. 64 V
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load: a = 90° a. Sketch the output voltage waveform. a b. Determine the ripple factor. VA= 240 V RL 752 CB A-B A-C B-C B-A CA C-B a Vc 27
Find Vpc if VAN = VBn = Vcn= 120 volts... Half-wave Three-phase Rectifier Conduction Waveform Periodic Time (T) A B A 90° 180° 360 450° 540 time 270° -V VAN VeN VaN VaN VEN Voc4 Voc 150 120° 270 390 510° time 30 Output Voltage Waveform
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 162 V and the firing angle of the SCR is 60 degrees, the peak voltage of the input sinusoidal would be: O A. 197 V O B. 228 V O C. Can't tell; need more information. O D. 340 V O E. None of the other choices are correct
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms and rectifier losses are 4W. The power efficiency of the rectifier is: O A. 58 % O B. None of the other choices are correct O C. 100 % O D. 80 % O E. 67 %