Example 2 A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a concentrated load of 10 kN at a point 1 m from one of the supports. Determine the maximum fiber stress and the stress in a fiber located 0.01 m from the top of the beam at midspan.

Example 2 A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a concentrated load of 10 kN at a point 1 m from one of the supports. Determine the maximum fiber stress and the stress in a fiber located 0.01 m from the top of the beam at midspan.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Given : Modulus of elasticity, E = 120 GPa = 120 × 103 MPa

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to…

A: Given data- Diameter of the punch = 20 mm, thickness = 8 mm, force = 110 kN, To Find- The value of…

Q: Problem 105 A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig.…

A: Given : Weight of bar AB = 800 kg Allowable stress = 90 MPa in bronze Allowable stress = 120 MPa in…

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: For the given beam,

Q: Determine the stress in a fiber (in psi) located 1inch from the top of the beam and 4 feet from the…

Q: As shown in the figure below, determine the internal loadings at point C. B 0.1 m 0.5 m C A -0.75 m…

Q: Beam AZ, 2 in wide by 4 in high, is subjected to a loading condition as shown. Determine (a) the…

Q: A wire cable was was used to suspend a 500 pound support beam. The orginal length was 12 feet. The…

A: Original length, L=12' Stretched length, L'=12.01' Therefore, change in length,x=12.01'-12'=0.01'

Q: Find normal, tangential and resultant stresses across a plane through the point at 480 to the major…

A: Principle stresses δX=100N/mm2 and δY=40N/mm2 θ=48∘

Q: 4 kN 50 mm 500 mm 4 kN 15 mm

Q: Beam AZ, 2 in wide and 4 in high, is subjected to a loading condition as shown. Determine: a. the…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

Q: A thin-wall tube, made of a unidirectional graphite/epoxy lamina with a fiber direction 0 to its…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

A: Consider the free body diagram;Given;Young modulus, E=Poisson ratio, v=0.3

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

Q: Example 2 A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a…

A: Draw free body diagram Consider the moment equilibrium about point A RB×4=10×1RB=2.5 kN Consider…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: B find the max Value of (P) that can be applied on the Cantilever beam Shown in figure, knowing that…

A: Consider the given beam. Calculate the moment in the beam as follows. M=Pcosθ×450=P×35×450=270P N·mm

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

Q: 9. A titanium T-bar having cross-sectional dimensions shown in Fig.9 is 320mm long and cantilevered…

Q: 5. The aluminum alloy bar has a circular cross section with 20-mm diameter and a shear modulus of 28…

A: We will use shear equation.

Q: Situation 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

A: Given : σx=-160mpaσy=-100mpaτxy=80mpa

Q: If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below

A: Moment intensity and cross section of I section have been given and it has been asked to determine…

Q: A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a concentrated…

A: to find max fibre stress

Q: A point in beam experiences a tensile stress (due to bending) of 50 N/mm2 and a shear stress of 20…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Example 2
A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected
to a concentrated load of 10 kN at a point 1 m from one of the supports. Determine
the maximum fiber stress and the stress in a fiber located 0.01 m from the top of the
beam at midspan.
Please answer 6

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem #2 (5 points): Fig. 2 shows aluminum hollow rods (outer diameter is 2 in. and inner diameter is 1.5 in.) that are fixed to rigid walls. The gap between the rods is 0.005 in when the temperature is 60°E. If the temperature is 200°F, what is the stress in each rod? aai = 13 x 10/F, Eai = 12 x 10 ksi %3D 0.005 in. .8 in. Fig. 2 Page | 1
A cantilever beam, 70 inm wide by 290 nm high and 8 m long, carries a load that varies uniformiy from zero at the free end to 1300 N/m at the wall, Determine the magnitrde of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answer must be in MPa Next • Previous
C. A rigid steel bar is suspended horizontally by 1m steel rod at one end and 2m bronze rod at the other end as shown. Neglecting the mass of the steel bar, at what distance X (in meters) from the steel rod should a 20 kN force be placed so that the steel bar will remain horizontal? Also, calculate the stresses in steel and bronze rod (in MPa). Use the following data. Steel, st Bronze, Br Br. 2m 20000 N Area (mm²) 600 300 St. 1m -X- E(GPa) 200 83 10 m
Q2/ the structure shown below, support from fix at the left , the max normal at bronze =200 MPA, Find area of bronze , normal stress at both steel and aluminum 10 KN Steel Aluminum, A= 100mm? A=200mm? Bronze, A=? 8 KN 5 KN 5 KN 3m 2m 1 m
A steel rod is stretched between two rigid walls and carries a tensile load of 5000N at 20oC . If the allowable stress is not to exceed 130 MPa at -20oC, what is the minimum diameter of the rod? Assume teta=11.7 mueM/moC and E= 200 GPa.
6. In Fig. 6, a 1.5 m long cantilever beam with a circular cross section (R = 100 mm) and two symmetrically positioned longitudinal holes is loaded by a concentrated force P at its tip. The material is a titanium alloy with a 600 MPa maximum allowed working stress when bent. Find the maximum permitted vertical force P value. 1.5 m Radius= R = 100 mm Radius of hole =
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A beam shown in Figure 7.7 is made of T beam, determine maximum shearing stress develop due to various type of loading. w- 3kN/m A B 2.0m 2.0m 2.0m
Problem 03
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 250-mm-gage length. Using E = 110 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.
Problem 2 A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa), located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. 2m B 10kN/mm 4m C 2m Steel Aluminum 42 mm 20 mm 13 mun
An aluminum bar having a cross-sectional area of 160 square millimeters carries the axial loads at the positions shown in the figure. Assume that the bar is suitably braced to prevent buckling. E = 70 GPa. 35 KN 15 KN 30 KN 10 KN -> 0.8 m 1.0 m 0.6 m B FIGURE 9 Determine the deformation at segment AB Determine the deformation at segment BC. Determine the deformation at segment CD. Determine the total deformation of the bar.