wheExample 12.2. Design the salient dimensions of a syphon well drop for thefollowing particulars :Fall= 3.8 mGeneral ground levelFull supply depthBed level upstreamDischargeBed width upstream and downstream = 2.4 m= + 163.36 m%3D= + 162.83=1 cumec%3D

Answered: Image /qna-images/answer/c957848e-e552-441b-9b60-452776373fde.jpg

Example 12.2. Design the salient dimensions of a syphon well drop for the following particulars : Fall = 3.8 m = + 163.36 m General ground level Full supply depth Bed level upstream Discharge Bed width upstream and downstream = 2.4 m =75 cm %3D = + 162.83 =1 cumec %3D %3D

Example 12.2. Design the salient dimensions of a syphon well drop for the following particulars : Fall = 3.8 m = + 163.36 m General ground level Full supply depth Bed level upstream Discharge Bed width upstream and downstream = 2.4 m =75 cm %3D = + 162.83 =1 cumec %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A circular culvert of 1.532 m diameter, flow Q = 2.32 m3 / s, depth 1 m and n = 0.014, calculate the…

A: Discharge (Q) = 2.32 m3/sDiameter of culvert (d) = 1.532 mDepth of water (y) = 1 m n = 0.014To…

Q: Consider that the flow rate of 0.020 cumecs is being conveyed from Reservoir A to Reservoir B.…

Q: 4. Find the dimensions of a concrete lined open channel used to convey a discharge of 70 m/s. The…

A: Given data Discharge Mannings roughness coefficient Side slope Bed slope

Q: Estimate the average depth. ATTACH YOUR SOLUTION. For a drainage basin of 600 km², isohyetals drawn…

Q: Question: Identify the types of water surface profiles that can be observed in the following channel…

Q: A flood occurs in a main channel having a trapezoidal section (side slope on both sides: 2H to 1V)…

Q: QUESTION 1 A horizontal well with a measured depth of 10,000 ft. can be approximated as being…

Q: 7. Manning's equation is not used to calculate

A: To find : Mannings equation is not used to calculate what.

Q: .Design Earthen Channel using Lacey's Regime Theory having following Data:

A: Discharge Q = 115 cumecsSlope S = 0.00022 m/mChannel side slope z = 2 1v:zhLacey' silt factor f =…

Q: check the stability of shown gravity dam if you knew that there is an effect of earth quake with k,…

A: (i) water pressure P=12γwH2 ( H=80 m and γw=1 ton/m)P=12×1×802=3200 ton at (h=H3=803=26.67 m…

Q: Select the false statement: a) The specific force per unit width of the channel is approximately…

A: Given questions about open channel flow.

Q: 3.1 A basin has a rectangular shape with four raingauges on each corner as shown in fig. below. The…

A: Dividing the rectangle shaped basin into 4 equal parts as 10 km*5 km= 50 km2 Consider rain gauge…

Q: What is the elevation of the water line at the bottom if the volume of reservoir is computed by end…

A: Given,Volume of reservior=26000 cu mA1 =3000 sq mA2 = 2,600 sq mA3 =2000 sq mElavation of water…

Q: Problem No. 1 A 9m log (SG = 0.67) is partially submerged in river (SG = 1. 03). Determine the…

Q: The following information are given: Mud density= 10 ppg, depth=D11000 ft., It is required to use…

A: The given data is shown below: Mud density=10 ppgDepth=11000 ftHydrostatic pressure=450 psiWater…

Q: Q#2: A rectangular notch is 1m wide. Water flows over this notch to a depth of 150mm. Then the same…

A: Given data Rectangular notch Width Depth Triangular notch Coefficient of discharge Angle To find…

Q: 12. Given the following data for a stream of uniform flow: 15pts A = 6.97 sq.m. P = 9.76 m S=0.007…

Q: Calculate the end areas for depths of fill from 0 to 20 ft using increments of 2 ft for level…

Q: Estimate the wetted perimeter of a circular annel having radius R and depth d, if the

A: To find : Wetted perimeter.

Q: 4. Estimate the discharge of water through a

A: To find : Discharge of water.

Q: Describe the procedure of double hydrometer test.

A: Double hydrometer test has been described as one of the most suitable tests for categorizing…

Q: Determine the wetted perimeter for the channel section shown below for y=3.48m 20m Answer: 1m +₁+ 5…

Q: Design the salient dimensions of a syphon well drop for the following particulars: Fall = 3.8 m…

Q: Determine the other alternated depth in meters of the rectangular channel section (width = 3…

A: Given data, One alternate depth y1 = 5 m Width B = 3 m Flow rate at both section 1 and 2 are same Q…

Q: Problem: Determine þPn for the short column shown. fy = 60000 psi and f'c = 4000 psi. 3" & = 8" 8…

A: A short column is the one whose ratio of effective length to its least lateral dimension is less…

Q: 5. The ratio between hydraulic radius and hydraulic depth of a triangular channel is 31/100,…

A: Please refer the attached image for complete solution. THANK YOU.

Q: How to use Hazen's formula to estimate the K of an aquifer ?

A: Hazen FormulaHazen developed formula (1892; 1911) and developed a formula for estimating the…

Q: A dam cross-section is a square facing a water depth of D=15m. Assuming a 1m strip for analysis and…

Q: Problem: Example: Given the following data of a stream of uniform flow: h h=height of water = 1.20m…

A: step 1-

Q: .Design Earthen Channel using Lacey's Regime Theory

A: Given: To design Earthern channel using Lacey's regime theory

Q: (Use Gumbel method) A river has following character: Average Q = 10,000 m^3/sec Standard deviation S…

A: Q=10,000m3/secStandard deviation=σ=3000m3/secXT=15,000m3/sec

Q: A pipeline carrying water has an average height of irregularities projecting from the surface of the…

A: Average height of irregular projecting from the boundary (k) = 0.155 mmSurface of pipe is…

Q: A 600 mm diameter horizontal pipe with a length of 1500m and C=120. the pressure gage attached…

A: The total head loss of a fluid as it moves through a fluid system is the sum of the elevation head,…

Q: A channel has been designed to convey clear water to a fish hatchery. The design calls for aflow…

A: The objective of the question is to determine if the existing design of the channel is adequate to…

Q: . The ratio between hydraulic radiu ydraulic depth of a triangular char 1/100, calculate the side…

Q: Drawdown in the pumping test refers to: a) The amount of water level decline in a well due to…

A: The ground water which is stored between the rocks are called as aquifer. The aquifers are…

Q: I need help on this problem Manning equation problem for parts a, especially rearranging the…

A: R (hydraulic radius) = A(area)/P(perimeter) = 250*20/(250 + 2*20) = 17.24 Q = 25000 ft3/s Q = 1/n x…

Q: 91:50, calculate the depth of the channel if the bed slope is 1 in 3000 and C = 50.

A: To find : Ratio between maximum discharge and top width.

Q: If you know that the respective distance of piezometers from the well have ( 12m , 25m)…

A: Given data : r2=25 mr1=12 mQ=50 m3/sh2=10 mh1=6 m

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

whe
Example 12.2. Design the salient dimensions of a syphon well drop for the
following particulars :
Fall
= 3.8 m
General ground level
Full supply depth
Bed level upstream
Discharge
Bed width upstream and downstream = 2.4 m
= + 163.36 m
%3D
= + 162.83
=1 cumec
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1#: For the concrete Dam shown in figure, determine the total average seepage for the given permeable strata by drawing Flow Net. The detail dimensions are given on the figure. The head of water on upstream side is 6ft and on downstream side is 1ft. Assume of Nf= 3, Nd= 6 and rectangular flow elements. Use paint or graph paper. SIR PLS, GIVE ME PROPER AND CORRECT ANSWER WITH FULL DETAILS AND ALSO USE PAINT OR GRAPH PAPER. THANKS
Water flows in a rectangular channel at a depth of 20 cm and with a velocity of 14 m/s. If a downstream sill forces a hydraulic jump, estimate the to the nearest two decimal places. downstream depth after the hydraulic jump in unit of m. Round
1. Draw the iso structure and iso pach map from the well information using ground level (14 ft K.B.) and sub sea measurements. The water oil contact is estimated to be at 2600 ft sub sea. Which well would you expect to be the best oil producer and which well would be the best water injection well? Well # Elevation Depth to Sand(K.B.) 3654 Pay Thickness(ft) 38 TI 1090 1000 1025 1024 W-1 W-2 W-3 3430 3589 3668 44 9. 33 W-4 W-5 W-6 W-7 W-8 1055 1078 1035 1023 3679 3575 3834 3658 41 9. 37 36 21 1065 1010 1076 1057 W-9 W-10 3860 3540 3478 21 43 4 W-11 W-12 3576 Well #1 Well #6 Well #11 Well #5 Well #3 Well #2 Well #9 Well #4 Well #10 Well #7 Well #8 Well #12
I need the answer as soon as possible
A line source of strength 15 m/s is situated within a uniform stream flowing at -12 m/s (i.e. right to left). At a distance of 0.6 m downstream from the source is an equal sink. How far will the stagnation points be from the nearest source/ sink?
Do not give answer in image and hand writing
B- The following table representing the relation between the recorded discharge (Q) with the water levels (W.L.) . Use a value of a = 7.50 m and Estimate the discharge corresponding to a gauge reading of 10.5 m .
There are three wells (A, B and C) along the hillslope, completed into the sand deposit (completed to points A, B, C). The screen for each well is shown and the point of elevation of the screen is considered at the mid-point of the screen. What is the hydraulic head, pressure head, and elevation head at wells A, B, and C (mid-points of the screens)? Which way will groundwater tend to flow, from A to B or from B to A? Please show how to calculate the vertical hydraulic gradient between A and B and indicate the direction of the gradient (up or down).
Read the question carefully and give me answer according to the question
please provide complete solution with formula
Please do the highlighted a and b on excel with the data provided, Soil mechanics, Thank you!
Use the Clark unit hydrograph procedure to compute and plot the 3-hr unit hydrograph for a watershed that has an area of 1,100 km^2 and a time of concentration of 5 hr. The Clark storage coefficient is estimated to be 4 hr. Use a 1-hr time interval for the computations and apply the U.S. Army Corps of Engineers synthetic time-area relationship. Extend the unit hydrograph to t = 25 hr to capture the recession limb.