Estimate the average depth. ATTACH YOUR SOLUTION. For a drainage basin of 600 km², isohyetals drawn for a storm gave the following data: ... Isohyetals (interval) (cm) Inter-isohyetal area (km?) 15-12 12-9 9-6 6-3 3-1 92 128 120 175 85 A 1.741 cm B 7.41 cm 7.14 cm 4.71 cm

Q: Problem 4 Derive the shear and moment equations for each beam segment.

A:

Q: Determine the displacement at C and the slope at B. EI is constant. Use the moment-area theorems. |A…

A:

Q: What would be the maximum and minimum weight that can be applied without causing the plock on the…

A: To find maximum and minimum weight of block

Q: The state of stress at a point is the result of two loadings as shown in figure. When acting alone,…

A: For the two loadings act simultaneouslythen resultant (absolute) shear stress at that point with…

Q: A,f, 107.4 mm 0.85/,'b Ca/B =107.4 mm / 0.85

A: Given data,

Q: 1. Express the two forces shown as Cartesian vectors. 2. Determine the magnitude and coordinate…

A: Given:- The magnitude of the force along with AB = FAB = 200 N  The magnitude of the force along…

Q: 2. Compute for the moment of inertia about xo and yo of the following figures. a) b) 100 mm 100 mm…

A:

Q: 2.3.2 If the beam section of Prob. 2.2.3 is reinforced with 3-25 mm diameter steel bars in the…

A: Given Data: fc = 30mpa 3-25 mm dia steel 65mm from the extreme fiber

Q: M Deter MINE THE MAX Dez of the Beam

A:

Q: Determine the force F at the end of the beam C so that the displacement at C is zero. El is…

A: Given: Displacement at end C is zero Required: Force F

Q: A W30x90 A36 steel girder spans 12 m on simple supports. It carries a uniformly distributed load of…

A: a. To determine the required section modulus, we need to calculate the maximum bending moment the…

Q: 5. Sieve analyses were performed on two soils. The table below summarizes the results of these…

A: Given:- The result of the sieve analyses are given  Sieve No.  Diameter Percent passing for Soil…

Q: depth h of the water.

A:

Q: For the beam and loading shown, (a) derive the equations of the shear and bending-moment curves, (b)…

A: Given overhanging beam with loading conditions and asked to draw SFD and BMD.

Q: A beam has a cross-section as shown. At a section where the shear force is 12 kN, 100 mm a.…

A:

Q: For a state of plane strain, the normal strain are given by €xx = 1000 x 10-6, € = 200 x 10-6 and…

A: Normal Strain,

Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…

A:

Q: 3.3 Vertical Alignment 53 ELEMENTS OF VERTICAL CURVE DESIGN An equal-tangent vertical curve is to be…

A: I have tried to solve this problem and also write the given data in diagram plz have gone through it

Q: The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B…

A: Given Data Cross sectional area at section a-a = 1in. × 0.25 in. Diameter of bolt shank (d) = 0.5…

Q: 5. Calculate the minimum passing sight distance required for a two-lane rural roadway that has a…

A: The formula of minimum passing sight distance is given by,

Q: 9. For the three-hinged arch shown, determine the reactions at A and B. The vertical distance…

A:

Q: 1. A reservoir with a surface area of 300 ha had the following average values of parameters during…

A: saturation vapour pressure for 32o. From the table of temperature and saturation vapour pressure we…

Q: Summary of Answer: Suction Hydraulic Head 1 Head 42 Conductivi Difference ty (K) Suction Head Total…

A: Consider the given data z1=0.8=-80 cmz2=1.9=-190 cmz1-z2=-80+190=110 cm Total head, h=ψ+2z=gravity…

Q: As shown in the figure compute the amount and location of the vertical and horizontal components of…

A: Given data,radius is 7.5mL=10mFINDAmount and location of vertical and horizontal component

Q: 15 kN/m 90 kN 50 kN D C 9 m -9 m 6 m

A: Solution: Given data: E=70 GPaI=95×106 mm4

Q: What are short-fiber composites? The critical fiber length. And the factors Chat affecting this…

A: Short-Fiber composites :  Short-fiber composites are composites with discontinuous fiber…

Q: Refer to the hydroelectric plant as shown in the figure. Determine the amount of power transferred…

A: GIVEN DATA:-⇒Diameter of pipe= 300mm  OR 0.3 m⇒Discharge (QB)= 1.7 m3/s⇒Frictional head loss= 4 m

Q: Determine the coordinate direction angles of FR- Express your answers using three significant…

A:

Q: Determine (a) the shear strains at all corners and (b) average normal strain that occurs along…

A:

Q: Choose the correct one and explain it

A: Given data : Normal stress in X direction (σX)=5 MPaNormal stress in Y direction (σX)=5 MPaMajor…

Q: Design Average Strength Strength (MPa) Specimen Diameter Batch No. Strength Age (days) (Mpa) Load…

A:

Q: Solve the reactions at the supports. 20 k- A 1.5 k/ft 12 ft- Hinge 1.5 k/ft 12 ft- B 12 ft 12 ft

A:

Q: P7.3. Determine the axial load, moment, and shear at point D of the three-hinged parabolic arch. 15…

A:

Q: Q1. Find the horizontal thrust of the water on each foot of width of the sluice gate, given y₁ = 7…

A:

Q: Hello! Would it be possible to included a step by step solution without skipping something and add…

A:

Q: P7.2. Compute the reactions at supports A and E of the three-hinged parabolic arch in Figure P7.2.…

A: Given:-  a three hinged arch as shown below

Q: Problem I. The masses of the frictionless cylinders A and B are 2.0 kg and 1.0 kg, respectively.…

A:

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

A:

Q: A 3" diameter bar is supported by a smooth pin in C and a cable from A to B around the smooth peg at…

A: Given: Diameter of bar = 3'' , Diameter of cable = 0.6'', Wt. of bar = 2500lb/ft3

Q: Alum at a rate of 20 mg/l is added to an incoming discharge of 0.5 m3/s which carries 250 mg/1 of…

A: 1. Alum added at a rate of 20 mg/l.2. Incoming discharge: 0.5 m³/s3. Incoming discharge carries 250…