Answered: EXAMPLE 10.6 Discretize the equation =0…

EXAMPLE 10.6 Discretize the equation =0 at node (i, j) of an interior corner axəy with the convection boundary condition as shown in Fig. 10.8. i, j+ 1 i-1, j i+ 1.j T h i, j-1 Ar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Seatwork Insulated B T2 D Insulated Consider the composite of two materials combined in parallel paths with the ends maintained at uniform temperatures as illustrated in Fig. Various quantities are specified: A, = 0.2 m2, k, = 20 W/(m . °C), A2 = 0.4 m?, k2 Calculate the rate of heat transfer Q across the composite medium. %3D = 15 W/(m · °C), L = 0.5 m, T, = 150°C, and T, = 30°C,
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. 1. Ts. 1} Steam 12. T8.2} Insulation (a) If the insulation is 27.5 mm thick and its inner and outer surfaces are maintained at T1 = 800 K and T2 = 490 K, respectively. what is the rate of heat loss per unit length (q') of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (q'), in W/m, and outer surface temperature T2, in K, for the steam pipe with the inner surface temperature fixed at T₁ = 800 K, inner radius r₁ = 0.06 m, and outer radius r₂ = 0.14 m. The outer surface is exposed to an airflow (To = 25°C) that maintains a convection coefficient of h = 25 W/m²-K and to large surroundings for which Tsur = To = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.75 m long. The pipe surface temperature is 125 ° C, and the air temperature is 30 ° C. Convection coefficient = Answer W / m² ° C.
Consider the square channel shown in the sketch operating under steady state condition. The inner surface of the channel is at a uniform temperature of 600 K and the outer surface is at a uniform temperature of 300 K. From a symmetrical elemental of the channel, a two-dimensional grid has been constructed as in the right figure below. The points are spaced by equal distance. Tout = 300 K k = 1 W/m-K T = 600 K (a) The heat transfer from inside to outside is only by conduction across the channel wall. Beginning with properly defined control volumes, derive the finite difference equations for locations 123. You can also use (n, m) to represent row and column. For example, location Dis (3, 3), location is (3,1), and location 3 is (3,5). (hint: I have already put a control volume around this locations with dashed boarder.) (b) Please use excel to construct the tables of temperatures and finite difference. Solve for the temperatures of each locations. Print out the tables in the spread…
The composite wall of an oven consists of three materials, two of which are of known thermal conductivity, ka = 20 W/m · Kand ke = 50 W /m · K, and known thickness, LA = 300 mm and Lc = 150 mm. The third material, B, which is sandwiched between materials A and C, is of known thickness, Lg = 150 mm, but unknown thermal conductivity kg. ka ke Air T., h Under steady-state operating conditions, measurements reveal an outer surface temperature of T, = 20°C, an inner surface temperature of T, = 600°C, and an oven air temperature of T = 800°C. The inside convection coefficient h is known to be 25 W/m? · K. What is the value of kg?
Q5) For laminar free convection from a heated vertical surface, the local convection coefficient may be expressed as hy = Cxx-1/4, where h, is the coefficient at a distance x from the leading %3D edge of the surface and the quantity C, which depends on the fluid properties, is independent of x. Obtain an expression for the ratio hx/hx, where x is the average coefficient between the leading edge (x = 0) and the x-location. Sketch the variation of h, and h, with x.
Problem 6. ART TAT Consider the cylindrical pipe shown in the figure. Heat is being generated in the pipe wall at a rate of R in units of W/m³, and the thermal conductivity of the wall is k, the heat transfer coefficients at the inside and outside of the pipe are h; and ho, respectively. At a given location along the pipe axis, the temperature of the fluid flowing inside of the pipe is Ti and that at the outside is To i. ii. Find the expression for the temperature distribution in the pipe wall. Find the total heat transfer rate from the pipe to both fluids.
The heat flow within a building is increasing or decreasing exponentially E to power 3t in line withtemperature difference which is t degrees ( C) with the outside surroundings.Estimate and explore the growth rate graphically when the temperature difference changes from -20degrees to + 20 degrees (C)
11:04 & NI A ll 95%Ï mlms.hu.edu.jo/mod/quiz/at :D Question 1 Not yet answered Marked out of 2.00 P Flag question In the figure shown, K, 25 cm, Lg = 1.30×LA ;Ti,00 2 = 581°C, h, , = 60 W/m K. T, = 160 °C, h = 35 W/m K. Neglect contact = 20 W/m.K, LA= 800 °C. Also; i,2 0,00 resistance. What is the temperature of T, (°c)? LA LB To,00 KR hi KA ho, B T, Select one: A. 438.13 B. 409.10 C. 416.75 D. 430.98 E. 424.21 ΝEXT PAGE
2. The slab shown is embedded in insulating materials on five sides, while the front face experiences convection off its face. Heat is generated inside the material by an exothermic reaction equal to 1.0 kW/m'. The thermal conductivity of the slab is 0.2 W/mk. a. Simplify the heat conduction equation and integrate the resulting ID steady form of to find the temperature distribution of the slab, T(x). b. Present the temperature of the front and back faces of the slab. n-20- 10 cm IT- 25°C) 100 cm 100 cm