EX2: (Buck dc-dc converter. Evaluation of the output voltage ripple) A buck converter has the following specifications: Vin= dc input voltage =50 V, D = duty cycle=D0.4, L=400 µH, C=100 µF f,= switching frequency = 20 kHz, R=20 2 Assuming that the converter is ideal, calculate: a) The output voltage. b) The maximum and minimum inductor current values. c) The output voltage ripple.

EX2: (Buck dc-dc converter. Evaluation of the output voltage ripple) A buck converter has the following specifications: Vin= dc input voltage =50 V, D = duty cycle=D0.4, L=400 µH, C=100 µF f,= switching frequency = 20 kHz, R=20 2 Assuming that the converter is ideal, calculate: a) The output voltage. b) The maximum and minimum inductor current values. c) The output voltage ripple.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
Explain the operation of both signal- and three-phase rectifier circuit by making reference to the sketched waveform.
Creating buck-boost converter diagram using the following: Voltage: 12V-5V The diagram includes voltage regulator.
B. A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R=25 and L - 10 mH. The firing angle a= 45° and the current extinction angle B-230". It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (c) Determine the average load voltage and current. (d) Determine the rms load voltage and current. (e) Determine the efficiency of the converter
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
A step down de chopper is connected to an R5 2 and L-10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, lo and the peak to peak ripple current as an absolute value and as percentage of de value.
Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
In ............ mode of operation, fully controlled converter will keep a delay angle range between 90 to 180.
How to create a voltage converter from AC to DC using Diodes and capacitors?
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.
Design the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stage
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.