Task: Converting AC to DC by a 5V Zenner diode as a regulator. a) Use the online site: www. Tinkercad.com to connect the devices shown on the breadboard as illustrated in circuit of figure below. b) Display the voltage waveform with oscilloscope at: - Output of bridge (without capacitor and Zenner diode). - Capacitor output (without Zenner diode). - Load resistor output (connect Zenner diode). Measure the load voltage using a Multimeter. What is the output voltage? 5.10 V 50.0 Hr

Task: Converting AC to DC by a 5V Zenner diode as a regulator. a) Use the online site: www. Tinkercad.com to connect the devices shown on the breadboard as illustrated in circuit of figure below. b) Display the voltage waveform with oscilloscope at: - Output of bridge (without capacitor and Zenner diode). - Capacitor output (without Zenner diode). - Load resistor output (connect Zenner diode). Measure the load voltage using a Multimeter. What is the output voltage? 5.10 V 50.0 Hr

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
What is the zener diode and what are its advantages? In what region of their characteristic curve are zener diodes operated? At what value of zener current is the zener voltage normally specified? How does the zener impedance affect the voltage across the terminals of the device?
Consider the Zener diode circuit shown in Figure. The Zener Breakdown Voltage (Vz) is 5.6 V at Iz= 0.1mA. Zener resistance is rz= 10 0. What is Vo without load (RL= ) ? R= 0.5 ko Vo R Vps= 10 V
Draw the circuit diagram of a half-wave rectifier for producing a nearly steady dc voltage from an ac source. Draw two different full-wave circuits.
Use Zener diode to design a clipper circuit to obtain the output waveform as shown in the figure below? 6.9 V +25 V Clipper Circuit -15.7 V -25 V
4. A Zener diode is connected in a voltage regulator circuit as shown in figure.2. The Zener voltage at I, = 0 is 15V and Zener incremental resistance 0.22. (a) Determine the value of Ri such that Zener diode remains in breakdown if the load current IL varies from 50 to 500 mA and if the input voltage Vi varies from 20 to 30 V. Assume lzmin = 0.21zmax- 5. With continuation to Q.4, Determine the power rating of each element in a circuit. R; V1 Vz RL VL Figure.2
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
Determine the peak to peak ripple voltage and the ripple factor for a bridge rectifire using capacitor input filter. The load resistance is 2 kn while the d.c voltage across the loadis 12 V. Assume supply frequency to be 50 Hz and ideal diodes. The capacitor of 100 µFis used in the filter circute.
Solution of this question is required. Urgently plz
Draw circuit diagram with the help of diodes. The current vs voltage graph at the output of the circuit is shown below ...
Solution of this question is required. Urgently please.