A buck converter produces an output voltage of 100 V across a 100 Ohm load resistor. The output voltage ripple is 0.5 %. The output current ripple is 2 A. The dc supply is 200 V. The switching frequency is 1 kHz. The value of the inductor is: Select one: a. 25.00 milli Henry O b. 35.25 micro Henry O c. None of the above d. 88.55 micro Henry O e. 75.15 nano Henry

A buck converter produces an output voltage of 100 V across a 100 Ohm load resistor. The output voltage ripple is 0.5 %. The output current ripple is 2 A. The dc supply is 200 V. The switching frequency is 1 kHz. The value of the inductor is: Select one: a. 25.00 milli Henry O b. 35.25 micro Henry O c. None of the above d. 88.55 micro Henry O e. 75.15 nano Henry

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw output waveform for the following circuit. Suppose input is a pure square wave with a positive half at 10 V and negative half at -10 V for ideal diodes. D1 D2 220 R3 R1 1k R2 1k
In Buck/Boost converter of Duty cycle is 50% to 100%, then the output voltage will be less than the supply voltage greater than the supply voltage zero constant
electronic
A zener diode exhibits a certain change in VZ for a certain change in IZ on a portion of the linear characteristic curve between IZK and IZM as illustrated in Figure 5. Calculate the zener impedance.
C + + Vi = 20 V Vo peak to peak 5V The diode is a non- ideal with Vy = 0.7V Solve and draw the output waveform for the given clamper circuit
In a half wave rectifier, the sine wave input is 300sin300t. The average value of output voltage is? a. 67.453V b. 95.492V c. 63.694V d. 57.876V
A 60 Hz sinusoidal voltage is applied to a single-phase half-wave rectifier. The output of the rectifier would have a frequency of:
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
The thickness of the PN depletion region increases when diode is Your answer The function of zener diode is to provide a constant output voltage to a load. this process is called Your answer One types of diodes are typically used for power supply applications which always called Your answer
For a sinusoidal input of 40 V (p-p) to the given circuit, what is the minimum value of the output waveform? NOTE: use ideal diode -40 20 30 O -5 О 07