Design a regulated power supply with an input voltage of 220 V (RMS value) and output regulated voltage of 12V. Use Zener diode as regulating device. Provide the following for your design: a. Block diagram b. Schematic diagram c. Manual computation per section with corresponding output waveform. d. Show comparison of the input and output signal waveforms.

Design a regulated power supply with an input voltage of 220 V (RMS value) and output regulated voltage of 12V. Use Zener diode as regulating device. Provide the following for your design: a. Block diagram b. Schematic diagram c. Manual computation per section with corresponding output waveform. d. Show comparison of the input and output signal waveforms.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 V and V2=9 V. R DZ D1 Vin Vout v2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the circuit diagram of a half-wave rectifier for producing a nearly steady dc voltage from an ac source. Draw two different full-wave circuits.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
What is the zener diode and what are its advantages? In what region of their characteristic curve are zener diodes operated? At what value of zener current is the zener voltage normally specified? How does the zener impedance affect the voltage across the terminals of the device?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
In the blow figure.(need handwritten only ,otherwise downvote.)
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 v and V2=8 V. R DZ D1 Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform Windows hui