Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Th/Ta b) the ratio of the angle of twist of the shaft 0/0a T' (a) (b)

Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Th/Ta b) the ratio of the angle of twist of the shaft 0/0a T' (a) (b)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
A 180-mm length of 30 x 40 mm solid rectangular bar is loaded as shown in the diagram. The right end of the tube is fixed to a rigid frame while the left end is free. (a) Draw the stress element for point B at the top center of the bar (right end) and label the stress vectors acting on the element, including the stress magnitudes. (b) Draw the stress element for point C at the middle of the front face of the bar (right end) and label the stress vectors acting on the element, including stress magnitudes
All part plzz
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
Read the question carefully and give me solution according to the question... Give me both solution
(b) A cooling tube having the cross section shown in Fig. Q1(b) is formed from a sheet of stainless steel of 3 mm thickness. The radii c₁ = 150 mm and c₂ = 100 mm are measured to the center line of the sheet metal. Knowing that a torque of magnitude T = 3 kNm is applied to the tube, determine (i) the maximum shearing stress in the tube (ii) the magnitude of the torque carried by the outer circular shell Neglect the dimension of the small opening where the outer and inner shells are connected. Hint: q - T 2A q=rt, T = Fr. Fig. Q1(b)
6.
Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress th/Ta b) the ratio of the angle of twist of the shaft Op/0a T' T' T T (a) (b)