Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Th/Ta b) the ratio of the angle of twist of the shaft 0p/0a T' T' T

Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Th/Ta b) the ratio of the angle of twist of the shaft 0p/0a T' T' T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A strain gauge rosette that is attached to the surface of a stressed component gives 3 readings (ɛa = A, &b = B, &c = C). If the strain gauge rosette is of the Dº type (indicating the angle between each of the gauges), construct a Mohr's Strain Circle overleaf. You should assume that gauge A is aligned along the x-axis. Using the Mohr's Strain Circle calculate the: (i) principal strains (1, 2)? (ii) principal angles (1, 2)? You should measure these anticlockwise from the y-axis. (iii) maximum shear strain in the plane (ymax)?
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
(b) A cooling tube having the cross section shown in Fig. Q1(b) is formed from a sheet of stainless steel of 3 mm thickness. The radii c₁ = 150 mm and c₂ = 100 mm are measured to the center line of the sheet metal. Knowing that a torque of magnitude T = 3 kNm is applied to the tube, determine (i) the maximum shearing stress in the tube (ii) the magnitude of the torque carried by the outer circular shell Neglect the dimension of the small opening where the outer and inner shells are connected. Hint: q - T 2A q=rt, T = Fr. Fig. Q1(b)
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 12.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L = 4 b, t = b / 25, c = 2b, b = 600 mm, e = 5 , f = 12