Data from an oedometer test using a clay specimen are plotted in the graph shown below. If the compression index is equal to 0.6, calculate the void ratio (e2) missing at Point C, which is associated with a vertical effective stress equal to 105 kPa eA(e₁ = 1.1, o=10 kPa)(e₁ = 0.8, o 60 kPa)B(e₂= ?,σ= 105 kPa) Clog ov'

The required void ratio (e2) is about 0.6542.Explanation:Recall that the slope of the virgin…

Answered: e A (e₁ = 1.1, o=10 kPa) (e₁ = 0.8, o…

Engineering

Civil Engineering

e A (e₁ = 1.1, o=10 kPa) (e₁ = 0.8, o 60 kPa) B (e₂= ?,σ= 105 kPa) C log ov'

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.14P: Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10...

See similar textbooks

Similar questions

Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
Calculate the R-value for the following materials: a. 4 in. thick brick b. 10 cm thick brick c. 12 in. thick concrete slab d. 20 cm thick concrete slab e. 1 cm thick human fat layer
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Bourdon-type pressure gauges are used in thousands of applications. A deadweight tester is a device that is used to calibrate pressure gauges. Investigate the operation of a deadweight pressure tester. Write a brief report to discuss your findings.
A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm at 45 minutes after the start of sedimentation (see Figure 2.25). What is the diameter D of the smallest-size particles that have settled beyond the zone of measurement at that time (that is, t = 45 min)? Figure 2.25 ASTM 152H type of hydrometer placed inside the sedimentation cylinder (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida)
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.