During the tension test on a steel rod within the elastic region, the followingdata were measured:Applied load = 102 kNOriginal diameter = 25 mmCurrent diameter = 24.99325 mmOriginal gauge length = 100 mmCurrent gauge length = 100.1 mmCalculate the Young’s modulus and Poisson’s ratio.

Q: Test No Temperature C Deformation rate(mm/min) Strain at break Youngs modulus (Gpa) Stress at…

A: Step 1: UTS mean Ultimate tensile strength. From the conventional stress strain curve, it is…

Q: A solid circular bar is acted upon by tensile force of 20N. The diameter of circular Bar is 10 mm.…

A: Given Tensile force, F = 20 N Diameter of bar, d = 10 mm  Change in Length of bar, L' = 0.2 m…

Q: A steel rod with a cross sectional area of 120 (mm] ^2 is stretched between two fixed points. The…

A:

Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and…

A:

Q: A strain gauge is attached to the surface of a circular shaft with a radius of 40 mm, as shown in…

A: Given, Radius of circular shaft = 40 mm Strain calculated by strain gauge = -200μ or -200 x 10-6  G…

Q: 4. The horizontal bar shown is supported by a pin at A and two rods with identical length. Determine…

A:

Q: A steel column has a sectional area of 0.126 m^2 and a length of 3 m. IF a 50000 KN load is applied…

A: Given data, Column sectional area A = 0.126 m^2 Column length L = 3 m Force applied F = 50000 kN =…

Q: Given data : Stress=70 Mpa Strain=0.5 Determine the value of E

A:

Q: The specimen shown is made from a 25 mm diameter cylindrical steel rod with two 38 mm outer-diameter…

A:

Q: Answer fast

A: Solution:a) Maximum Stress CalculationFormula:Maximum Stress = Fplastic  / A 3. Calculation:Maximum…

Q: A plate 2 m x 2 m x 20 mm is subjected to stress o, 100 MPa (tensile) and o, = 50 MPa (compressive)…

A:

Q: A steej two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E =…

A:

Q: If the angle of obliquity for the resultant stress at a plane which is 45° from the principal stress…

A: To find the ratio of stress in x-direction to stress in y-direction

Q: An aluminum rod with a semicircular cross section of radius r = 12 mm (Fig. a) is bent int he shape…

A: First we summarise the given data : r = 12 mm mean radius of circular arc = 2.5 m E = 70 GPa To…

Q: 16 mm B 3 mm 3 mm 16 mm 16 mm- -16 mm-

A: Draw the figure.

Q: Diameter of the metal bar, before and after load application was measured to be 100.00 mm and 99.99…

A:

Q: 30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected…

A: we have to determine the lateral strain

Q: Consider a metal bar 12.5 mm in diameter and 50 mm in length that is tested under uniaxial tension.…

A:

Q: Q- 7 b, A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given data- A bar specimen- Diameter d=36 mm, Change in diameter ∆d=0.0046 mm, Gauge length L=200…

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch  The cross-sectional area of…

Q: The tension of a specimen of steel having an initial diameter of 0.507 in. was tested using a gauge…

A: Given that,  We have to calculate yeild strength   Yeild strength = P / A

Q: agram as neces

A:

Q: 1.5-7 The data shown in the table were obtained from a tensile test of a metal specimen with a…

A:

Q: 7. Three rods of different materials are connected as shown in the figure. (a) Determine the maximum…

A:

Q: Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled…

A: the test is conducted in UTM.  the test is standardized by American testing society material .  the…

Q: An applied torque results in a shear strain (y) of 3.75 x 10-3 in a solid circular steel shaft. At…

A:

Q: 2.7 The following readings were recorded during a tensile test of a mild steel specimen 24 mm wide…

A: Given data, Width = 24 mm Depth = 10 mm Area = 240 mm2 Length l = 200 mm Graph for the first…

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: Mechanical properties of materials H.W.: The following data where obtained during the tensile test…

A: Mechanical properties are those properties of a material which can be observed under the action of a…

Q: A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The…

A: The temperature causes contraction on elongation in rod as per drop and rise in its value. If the…

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

A:

Q: The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm…

A: Load vs elongation table:   Load (kgf) Elongation (mm) A 4800 0.192 B 8400 28.8 C 7200 38.4…

Q: 2.Discuss elastic region in a tensile test and shear test. It is always linear. What is engineering…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A:

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

A:

Q: 3. A new material is being developed and tested in the lab. The column was made using the new…

A: To find the elastic modulus and vicose coefficient

Q: A Charpy V Notch (CVN) test was performed on a steel specimen and produced the readings shown in…

A: We have been given the following values: Sr. No Temperature(C) Toughness, Joule (N.m) 1.…

Q: At a temperature of 33.37 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time…

A: