Draw clearly the shear force and bending moment diagram for beam shown in figure, show all details values, distance, line or curve. Compute the magnitude and location of the maximum bending stress in the beam if the shape used is W410 × 60. 20 kN 60 KN 40 kN/m S0KN-m 2m 3 m Im

Draw clearly the shear force and bending moment diagram for beam shown in figure, show all details values, distance, line or curve. Compute the magnitude and location of the maximum bending stress in the beam if the shape used is W410 × 60. 20 kN 60 KN 40 kN/m S0KN-m 2m 3 m Im

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m 10 kN 6 m B…

Q: a) Draw the V and M Diagram and determine the maximum shear and moment experienced by the beam. b)…

Q: Consider a circular hollow section, with outer diameter dp (in mm), and thickness tp (in mm). The…

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

Q: 3. A cantilever beam 75mm wide by 250mm high and 6m long carries a uniformly distributed load of…

Q: Refer to the photo provided and please make sure your handwriting is readable. Given E = 200 GPa and…

A: PB = 80KN

Q: The internal shear force V at a certain section of an aluminum beam is 6.9 kN. If the beam has the…

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: shear force , V= 20 KN thickness of all pieces= 30 mm

Q: a (Figure 1: A three cell section)

A: Since the section is symmetrical about horizontal axis. The strip is thin, so we can ignore it in…

Q: For the beam and loading shown, consider section n-n and determine (a) the largest shearing stress…

Q: QI: Determine the maximum tension and compression stresses acting on the beam shown below and draw…

A: We will use bending and direct stress formula.

Q: A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the…

Q: H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of…

A: Given data, Required: (a) the maximum tension bending stress at any location along the beam (b)…

Q: The simply supported beam consists of a W460 × 82 structural steel wide-flange shape [E = 200 GPa; I…

Q: A W410 x 60 standard steel shape is used to support the loads shown on the beam in the figure.…

A: P= 132kN,w= 24kN/ma= 3mb= 2mFree body diagram of beam:-

Q: The cross-sectional dimensions of the beam shown in the figure are a - 4.4 in, b- 5.9 in., d - 4.8…

Q: 25 mm 200 mm V 100 mm 25 mm 25 mm 25 mm 200 mm 25 mm

Q: AWT230 x 26 standard steel shape is used to support the loads shown on the beam in the figure. The…

A: Determinea. Maximum tension bending stress. b. Maximum compression bending stress. Note:- For…

Q: The cross-sectional dimensions of the beam shown in the figure are a- 4.4 in, b- 5.9 in, d- 4.8 in.,…

Q: -51.476603223441mm, Determine the radius of the cross-section of the circular beam. Determine the…

A: E = 90 GPaMaximum shear force = 508.4 kNP = 190 kNa = 2 mb = 1 mc = 3m Calculations for support…

Q: P B -0.4 m P 0.2 m D 72000 5640192 12 mm 11 4mm G NA ↑ 96 mm 6mm E TL Figure (2)

Q: Figure Q6b shows a simply supported 3.75 m long beam with a solid round crosssection and a…

A: Determine the maximum compressive and tensile stress.

Q: 6. Compute the maximum tensile and compressive bending stress for the simply supported beam with…

A: A we have to determine the maximum tensile and compressive bending stress

Q: 4. Calculate the maximum bending stress and maximum shear stress on the cantilever beam shown below.…

Q: Situation #1: A hollow trapezoidal steel structural section, filled with concrete, has outside and…

Q: 3. A beam simply supported on a 12-m span carries a uniformly distributed load of 30 kN/m over the…

A: Given ; span = 12m UDL = 30kn/m

Q: Determine the concentrated load at midspan that can be added if the uniformly distributed load o is…

A: We have to determine the concentrated load at midspan that can be added if the uniformly distributed…

Q: 1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20…

Q: The values of axial stress (o) in kN/m2, bending moment (M) in kNm, and shear force (V) in kN acting…

A: Given- Area A=0.04 m2, Load P=50 kN, Axial stress, Bending moment & Shear force is required.

Q: Problem 1: A round solid shaft is subjected to torsion as shown. Find: 1- Maximum torsional shear…

A: T1 = 50 k ft T2 = 20 k ft Gs = 30 x 106 psi Gal = 15 x 105 psi

Q: A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown.…

A: A square box beam is made of 80 x120 mm s=50 mm allowable shearing force= 300N As the maximum…

Q: 350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and…

A: Bending stress is linearly proportional to depth. Compressive and tensile stress have same value but…

Q: For the simply supported beam with the given cross-section, the shear force diagram has been…

Q: PROBLEM 05: The schematic of a punch and washers is shown. Determine the force P needed to punch out…

Q: O 6.14 For a beam having the cross section shown, deter- mine the largest allowable vertical shear…

Q: Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending…

A: RA=RB=12×2×8+8×2 =24 kNx=23m Bending Moment at distance 'x'…

Q: A double tee cross section is used for the beam shown below. Assume the following lengths and loads:…

Q: 8" H E = 36,000 ksi 5" Max Bending Stress: 1.25" TYP A simply supported beam has a symmetric cross…

A: Given Vmax = 800lb Mmax = 2400 ft-lb Required Maximum bending stress

Q: 00144 0.01am 0.09m 0.0144m 0.09m For the beams shown below: 1- Draw shear force and bending moment…

A: Note:-As per the guidelines we are only supposed to answer first question. With three sub parts.…

Q: For the beam in figure 1, find the value and location of the largest tensile and compressive…

A: The objective of the question is to find the value and location of the largest tensile and…

Q: A simply supported steel beam of channel-type cross section is loaded by both the uniformly…

Q: A beam shown below has a T-shaped cross section. Determine t maximum compressive stress of the beam.…

Q: Calculate the axial force on members a and d for the truss system shown in Figure 1. Indicate…

Concept explainers

Planar Stresses

Question

Draw clearly the shear force and bending
moment diagram for beam shown in
figure, show all details values, distance,
line or curve. Compute the magnitude and
location of the maximum bending stress in
the beam if the shape used is W410 x 60.
20 kN
60 kN
40 kN/m
50 kN-m
D
2 m
3 m
Im

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
is strengthened by bolting two cover The wide-flange beam shown in Fig. plates 160 mm by 20 mm to the top and bottom flanges. If the maximum flexure stress is 140 MPa, compute the total force (a) in each cover plate and (b) in each flange. Neglect the weakening effect of the bolt holes. 160 mm 20 mm 20 mm 320 mm 20 mm €20 mm
A beam shown below has a T-shaped cross section. Determine the location of maximum compressive stress from left support of the beam. I = 87-49 in 4 400 16/ft 16001b 160016 I↓↓↓I LOFT #. £7 32000 lbft 2.914 in 5.886 in B -NA 34/00/6 4FT 10° 100016 -240016 1000lb dc -4000 16 ff V M
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
1 The simply supported beam is used to supports loads and moment as shown below. Draw shear and moment diagram then determine the maximum tensile and compressive stresses and the maximum shear stress. 150 mm 10 kN/m 20 mm 5 kN/m 10 kN.m 150 mm 3 m * Im 1 m 3 m B 20 mm