QUESTION 1a) Calculate the position of the neutral axis and the value of thesecond moment of the beam with a cross section as shown inFigure 1(a).-216 mm-72 mmFigure 1(a)b) If the beam of cross-sectional area Figure 1(a) that simply supported at both ends carriesa uniformly distributed load, 1.5 kN/m along its 2m length. Determine the maximumtensile and maximum compressive stresses.36 mm108 mmQUESTION 2a) A solid shaft of 50 mm diameter is subjected to 10 kNm torque. Determine the shear stressand angle of twist if its length is 2m. Given the rigidity of modulus is 90 GN/m².b) A solid steel shaft 5 m long with a shear stress of 80 MN/m² when twisted through an angle 4º.Given G= 83 GN/m², determine:i. The shaft diameteri. The power that can be transmitted by the shaft at 20 rpm.

Given:Required:Position of neutral axis and second moment of beamMaximum tensile and compressive…

QUESTION 1 a) Calculate the position of the neutral axis and the value of the second moment of the beam with a cross section as shown in Figure 1(a). -216 mm- C 72 mm Figure 1(a) b) If the beam of cross-sectional area Figure 1(a) that simply supported at both ends carries a uniformly distributed load, 1.5 kN/m along its 2m length. Determine the maximum tensile and maximum compressive stresses. 36 mm 108 mm

QUESTION 1 a) Calculate the position of the neutral axis and the value of the second moment of the beam with a cross section as shown in Figure 1(a). -216 mm- C 72 mm Figure 1(a) b) If the beam of cross-sectional area Figure 1(a) that simply supported at both ends carries a uniformly distributed load, 1.5 kN/m along its 2m length. Determine the maximum tensile and maximum compressive stresses. 36 mm 108 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
3. For the beam with cross-section shown: a. Determine the maximum tensile stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). b. Determine the maximum compressive stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). c. Determine the maximum shear stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). d. For the cross-section 2 m to the right of A, determine the normal stress at point D on the cross-section, and state whether this stress is tensile or 100 KN m compressive. e. For the cross-section 2 m to the right of A, determine the shear stress at point D on the cross- section. f. Determine the equations for the elastic curve, and for the slope of the elastic curve, for…
02) The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmax = 1936x(0.5). 2. IfG =30 GPa find the angle of twist at the free end of beam. Y 10 kN 25 NA 120 mm 15 500 mm Good Luck and be Green
Two vertical forces, each of magnitude P= 20 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 3 in. 3 in. 3 in. A 40 in. P -60 in. P 6 in. 2 in. 1 40 in. D The maximum tensile stress is The maximum compressive stress is required.) ksi. (Round the final answer to two decimal places.) ksi. (Round the final answer to two decimal places. Include a minus sign in the answer if
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.