H.W.1 /The cantilever beam in Figure below has a rectangular cross section with dimension(20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (oms) in the beam.(b) Find the maximum bending stress (amar) in point B and C in the beam (c)Sketch thebending stress distribution over the cross scction on which the maximum bending stressoccurs.Aв10 Ib/ftC20 ft60 ft

Answered: Image /qna-images/answer/81ef3619-efb4-4284-9594-bb8e9029fe77.jpg

1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (Gman) in the beam. b) Find the maximum bending stress (ama) in point B and Cin the beam (c)Sketch the ending stress distribution over the cross section on which the maximum bending stress ccurs. A в 10 Ib/ft 20 ft 60 ft

1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (Gman) in the beam. b) Find the maximum bending stress (ama) in point B and Cin the beam (c)Sketch the ending stress distribution over the cross section on which the maximum bending stress ccurs. A в 10 Ib/ft 20 ft 60 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P7-L In cach case,calculate the value of Q and i that are used in the shear formula for finding the shear stress at A. Alsa, show how the shcar stress acts on a differential volume element located at point A. fa2m 02m tazm al aim (d) al m 03m 03 m taim Fozm le) a5m falm 402m 0.3m talm 01m (c)
Flexure stress *Please answer in complete solution and draw the shear and moment diagram, Solve the Area moment of inertia*
Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply supported beam shown in the figure and (c) the shearing stress at a point 1m from the right support and 2 cm below the top. 5 cm 40 kN/m 16 kN m A 1-+-2 2 m m CF -2 m 16 cm
2
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
with FBD please Complete solution thank you
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm
Question stated in the picture. Detailed answer is needed
Please solve the problem in the picture
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
lute flexural stress. For the beam shown in Figure (3), given INA = 1.+ 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam.