Draw and illustrate the following statements: 1. Simply supported beam with a length (L) and a concentrated load (P) at the mid span 2. Fixed ended beam at a span of 3m with uniformly distributed load (w) within 2m from the left and a concentrated load 1m from the right end. 3. Overhanging beams with a uniform load (w) throughout the span (L) Amel

Draw and illustrate the following statements: 1. Simply supported beam with a length (L) and a concentrated load (P) at the mid span 2. Fixed ended beam at a span of 3m with uniformly distributed load (w) within 2m from the left and a concentrated load 1m from the right end. 3. Overhanging beams with a uniform load (w) throughout the span (L) Amel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

MN/m². 1005. A timber beam 150 mm by 250 mm is reinforced at the bottom only by a steel plate, as shown in Fig. P-1005. Determine the concentrated load that can be applied at the center of a simply sup- . 6 m long if n = 20, 0, < 120 MPa, and ow < 8 MPa. Show ported span that the neutral axis is 170.2 mm below the top and that I = 416 X 10° mm*. Ans. P= 13.1 kN 150 mm- 250 mm 100 mm 10 mm
*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers. PROVIDE COMPLETE SOLUTOTION WITH ILLUSTRATION. Use American standard steel design code
Problem 2 A 10-ft-span cantilever beam has a rectangular cross-section (10" x 20 ") and reinforcement with three # 8 (A, = 2.37 in²) The beam carries a dead load, including its own weight, of 1.65 kip/ft and a live load of 0.95 kip/ft. Use, concrete cover = 2.50", f.' = 3.50 ksi and f,= 60 ksi, check if the beam is safe to carry the above loads.
A compo beam is fabricated by bolting two 2.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The mod elasticity of the timber and the steel are 1970 ksi and 28800 ksi, respectively. The simply supported beam spans a distance of 17 ft and carries two concentrated loads P, which are applied as shown. Assume LAB=LCD= 4 ft, LBc = 9 ft, b = 2.6 in., d=13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,, o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1080 psi and 23900 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: (a) o, = (b) P= i LAB i B b LBC F Cross section C ksi, o, = kips. LCD i D ksi. 0000000
Q.2 The supporting beams for the pool deck in Fig.1 are designed as simply supported with effective span of 6.5 m. The beams have width b = 250 mm and effective depth, d = 400 mm. The imposed floor live load is 4 kN/m² and Grade C30 concrete (feu = 30 N/mm²) with unit weight of 24 k/m³is specified. a) Design the beam on Gridline B for Ultimate and Serviceability Limit States using the following design specifications: • Main reinforcement (fy = 500 N/mm²): 25 mm (tensile), 16 mm (compression) • Shear reinforcement (links) (fyy = 460 N/mm²): 12mm are (main bars), • Cover: 25mm b) Sketch the following reinforcement detail sections of your final beam design. (i) Sectional Elevation Longitudinal Section 2 6.5 m A 3.2 m B RC Beams 3.2 m (a) Floor Plan Section X-X RC Slab Fig. 1-Reinforced Concrete Deck Floor
Homework #8 60 #/' 12' fb = My/l = M/S fv=VQ/lb (general formula) fv=3V/2A (for rectangular sections) A 2x8 joist (b=1.5"; h=7.25") is loaded with a uniform load (w) of 60 #/ft on a simple 12' span. Determine the maximum bending stress (fb) and the maximum shear stress (fv) developed in the joist.