Consider pattern loading (skip loading) for live load (shown black on the sketch) for the simply supported beam with overhang. DL Vmax E 20' 8' M+ max WD = 1.2 x 2 = 2.4 k/ ft WL = 1.6 x 3 = 4.8 k / ft M- max a. Draw bending moment diagrams for three loading conditions. i) Live Load + Dead Load over entire span ii) Live Load over the simply supported beam + Dead Load over entire span iii) Live load on the overhang + Dead Load over entire span b. Using the bending moment diagrams for three skip loading you have calculated, show maximum positive moment and negative moment with corresponding location.

Q: What type of architecture is this?

A: Answer:- It is the METABOLISM TYPE ARCHITECTURE and it is Residential Building and/or Office…

Q: Define the term capillary fringe.

A: The capillary fringe is characterized as the saturated zone of water immediately just above the…

Q: When are shear plates used?

A: Shear Plate :  1.shear plate connectors provide a large bearing surface to resist shearing-type…

Q: The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete…

A:

Q: Describe Fellenius Method.

A: In situations where the effective angle of shearing resistance over the failure surface is not…

Q: Gable Roof design

A: gable roof is a type of roof design where two sides slope downward toward the walls – and the other…

Q: How many Types of doors.

A: To determine: How many types of doors.

Q: Construct a new floor plan so that every doorway would be visited once in the museum

A: Construct a new floor plan so that every doorway would bevisited once in the museum

Q: Explain pipe earthing

A: Brief concept- Earthing- It is a process by which charge is transferred to the earth with the help…

Q: How do you think are the details for cut bars and anchorages determined? Answer in 3-4 sentences…

A: Anchorage: The reinforcement bars are provided in the type of hooks and bends. The anchorage bars…

Q: All specific sizes recommended by CRSI below meet minimum requirements of ACI 318 Recommended End…

A: The Standard Specifications require that reinforcing steel hooks and bends conform to the provisions…

Q: Define Membranes for low-slope roofing.

A: Solution: 1. Low slope roofs are generally defined as the roofs that having the pitch which is less…

Q: In detail describe what are standpipes.

A: This question is related to the Pipe system from Environmental engineering from Civil Engineering.…

Q: 6. Using the equation of the magnetic field due to a single ring of charge, derive the formula for…

A: Step 1: Step 2: Step 3:don't forget to upvote :) thank you and comment if doubt exists Step 4:

Q: draw stair tread and riser = 270 & 187 mm stair slab and landing thickness = 150 mm

A:

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: y thermal bridging? thank you if you will answ

A: A thermal bridge, also known as a cold bridge, is a section of a building with much higher heat…

Q: What is Jet grouting?

A: The jet grouting can be defined as it is a soil stabilization or ground improvement method which…

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: Define spudding

A: For drilling a well in a gas and oil industry, this process is used at the beginning.

Q: A & C are incorrect, please re-work

A: As per question , I solve here only a and c. Find out - (a) Radius of curve  (c) Tangent length

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: Why compass box is covered with glass?

A: compass box is a box which contains magnetic needle.  A needle is pivoted inside the box which can…

Q: A CPLD is based on

A: A CPLD- Complex Programmable logic device It is a programmable device based on complexity PALs and…

Q: Define Vibrocompaction.

A: Vibrocompaction is a method in which the density of granular soils is increased to the appropriate…

Q: What is VMT?

A: as the acronyms having the various meaning for VMT.  but some important term is used in civil…

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: hat is volume anaylsis system?

A: Civil engineering is mainly concerned with the planning and detailing of the structure. So for the…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: what method did you use there

A: For forces in member , method of joints have been used and for displacement calculation virtual work…

Q: Arch 486 Detail Problem: 2023 Detail Problem Draw a pinned connection and a fixed connection for…

A: Fixed Connection: For a 2 dimensional structure, fixed connection has three reaction forces. They…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A: For resultant of the load to pass through point B. Reaction force at A (RA) = 0

Q: Define Core barrels

A: Following is the core barrel definition and uses

Q: what is footing

A: Answer Introduction The important elements of the building which give stability to the structure are…

Q: Differentiate half sectioning & full sectioning

A: Full  Sectioning  Half Sectioning  1. It is the full section view. 1. It is the half section view.…

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.