Do not use Al or chatgpt otherwise downvote A single-phase full-wave rectifier is connected to an AC source with a peak voltage of 170 V and a frequency of 60 Hz. The load resistance is 502. (a) Calculate the peak, average, and RMS value of the output voltage. (b) Determine the average power delivered to the load. (c) Find the peak inverse voltage (PIV) that the diodes must withstand.

Do not use Al or chatgpt otherwise downvote A single-phase full-wave rectifier is connected to an AC source with a peak voltage of 170 V and a frequency of 60 Hz. The load resistance is 502. (a) Calculate the peak, average, and RMS value of the output voltage. (b) Determine the average power delivered to the load. (c) Find the peak inverse voltage (PIV) that the diodes must withstand.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
For each circuit shown below, the input v, is a 60HZ, 12 volt peak sine wave. Sketch the waveform resulting at vo. Assume ideal diodes. What are its positive and negative peak values?
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Do not use AI or chatgpt otherwise downvoteA single-phase full-wave rectifier is connected to an AC source with a peak voltage of 170 V and a frequency of 60 Hz. The load resistance is 502. (a) Calculate the peak, average, and RMS value of the output voltage. (b) Determine the average power delivered to the load. (c) Find the peak inverse voltage (PIV) that the diodes must withstand.
4. In a single-phase full-wave bridge uncontrolled rectifier, the diodes have a reverse recovery time of 40 us. If the ac input voltage is 230 V, determine the effect of reverse recovery time on the average output voltage for a supply frequency of (a) 50 Hz and (b) 2.5 kHz.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
In the single-phase diode rectifier circuit shown in Figure 1 and a constant dc load current Ia = 10A, calculate, if vs is a sinusoidal voltage with V, i. the average output voltage ii. rms values of input current and current through each diode 120 V at 60 Hz, iii. the average power supplied to the load.