Do not use AI or chatgpt otherwise downvoteA single-phase full-wave rectifier is connected to an AC source with a peak voltage of 170 V and a frequency of 60 Hz. The load resistance is 502. (a) Calculate the peak, average, and RMS value of the output voltage. (b) Determine the average power delivered to the load. (c) Find the peak inverse voltage (PIV) that the diodes must withstand.

Do not use AI or chatgpt otherwise downvoteA single-phase full-wave rectifier is connected to an AC source with a peak voltage of 170 V and a frequency of 60 Hz. The load resistance is 502. (a) Calculate the peak, average, and RMS value of the output voltage. (b) Determine the average power delivered to the load. (c) Find the peak inverse voltage (PIV) that the diodes must withstand.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

B. Draw the circuit diagram of a clipper that will produce an output waveform below. From the outp waveform Voltage A is 8.7 and Voltage B is -9.7.Input peak-to-peak voltage is given as 20 volts. Assi Silicon diodes are used. 7 B 1. For the positive half cycle, the needed battery voltage is 2. For the negative half cycle, the needed battery voltage is
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.
(ii) Briefly explain the principle of operation of the rectifier circuit. Ensure to explain about the pair of diodes that conduct for the positive cycle and the pair that conducts for the negative cycle of the input signal. (iii) Suppose the input signal vs(t) is a sine wave with a peak voltage of 8 V and frequency of 50 Hz. Sketch the output signal across the load resistor R₂ with the expected peak voltage. Also state the ripple frequency beside the waveform. (iv) Explain why there is a short period between pulses when the output voltage is zero.
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
Topic: Full-Wave Rectification
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a).
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.
Determine the a.c. ripple voltage across the load of full wave rectifier which delivers 40 W to a load resistance of 150 ohm, and ripple factor is given as 1% A) 77.4 V B) 38.7 V C) 0.387 V D) 0.774 V
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
I need the answer quickly