Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A component made of 7075-T6 aluminum alloy has an edge crack of 1.4 mm in length. Plane strain fracture toughness of this alloy is given as 27 MPavm. Geometrical factor of the crack is given as 1.2.| (a) If this component is subjected to uniaxial tensile stress of 380 MPa, determine whether sudden brittle fracture will occur or not. (b) Calculate the maximum allowable crack size for this component in order not to be failed in brittle manner under a stress of 1000 MPa.
QUESTION 10 A cruise control system is implemented on an expensive ferrari and results in closed-loop dynamics modelled by the equation 3 dv/dt + 0.9 v = 0.8 r where r is the target velocity and v is the actual velocity and the time scale is seconds. Which of the following statements are true? Do not guess as incorrect answers are penalised. Only select the statements you are sure are correct. The system velocity diverges. The system has satisfactory dynamics. The system converges to a zero steady-state error. None of these. The system does not reach the required velocity. The system has slow dynamics."
Design a PID controller for this system.
In the example on the pages 29 30, the system will be stable if 0
Problem 1. controller, and G(s) = Consider the control system shown in Fig. 1, where De(s) is the 1 (s - 1)(s+5) 1) (5 points) Is the open-loop system stable? 2) (15 points) Assume that De(s) = K. Rewrite the closed-loop characteristic equation in the root-locus form 1 + KL(s) = 0. Sketch the root locus for L(s). Is it possible to stabilize the system using a proportional controller? == 3) (10 points) Assume that a PD-controller is used to control the system, i.e., De(s) KpKDs. Utilize the Routh-Hurwitz criterion to derive stability conditions for the closed-loop system. + Ro Σ Dc(s) G(s) -OY Figure 1: Control system in Problem 1.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
explain please. Which type(s) of systems will oscillate in response to a step function?
QUESTION 3 An open loop transfer function with a unitary feedback control system is given K by G(s) =- where K is the gain of the system. An open loop (s+1)(s+4) transfer function with a PID controller must be designed in order to yield a peak time of 1.047 s, and a damping ratio of 0.8. 3.1. Calculate the design point s, of the system 3.2. Calculate the gain and the zero(s) of the PID controller 3.3. Provide the block diagram of the compensated system with the PID controller
If the system is to be arranged in a closed-loop, with a controller gain K in the forward path and a unity negative feedback loop, what is the maximum value of K which could be used without the system becoming unstable? Assuming you use Figure Q5 for this, use a sketch to show how you obtained the values from the plot.
Find the differential equation and define the type of the control low. Draw the control structure. Problem 2 A pressure is measured with a sensor with range-1 to 10 bars. If it generates a current with range between 4 and 20 mA, please calculate the pressure if 10 mA is measured at the PLC Input;
control of mechanical system give me correct option
Problem 3. Consider the electrical circuit shown in Figure 3 (left). Assume that R₁ = R2 = 1 and C = 1F. 1) (15 points) Derive the transfer function G(s) = Vo(s)/Vs(s) of the electrical circuit. 2) (15 points) If a controller is used to control the system, then the block diagram of the closed-loop system is given by Fig. 3 (right). Suppose that the reference is a ramp signal, i.e., r(t) = t 1(t). Design a controller De(s) such that the closed-loop system achieves perfect tracking (e(t) = r(t) - y(t) → 0). Justify your design. a -> + US R₁i w C: iz iz i3 + R2 Vo RO Σ Do(s) G(s) OY Figure 3: Electrical system in Problem 3.