Answered: Determine the tributtary area/ft of…

Determine the tributtary area/ft of joists of a floor system consisting of 4 in. x 6 in. Southern Pine select structural joists spaced at 24 in. on center spanning 14 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft³) behaves as a liquid. Determine the…

A: The given data is: sw=150lb/ft3 Height of concrete in form=9 ft Force on form Ft=sw×z×A

Q: 4. Termite shields are placed on top of wood sills to protect floor joists from termite infestation.…

A: Solution for Question 4: True. The termite shields are placed on the top of wood sills to protect…

Q: Create a flow chart about safety criteria in highway engineering design.

Q: • Live load = 40 psf • Decking = 5 psf • Beams = 5 plf . Girder = 20 plf . Concrete density = 150…

A: Tributary area of Post A

Q: All question pertain to the following floor plan. The floor load is 60 lb/ft2. Ignore the self…

A: All the slabs on the floor are one way slabs, since the value of longer to shorter span for each…

Q: 3. Given: FLOOR SYSTEM DL + LL = 2 kPa, Fb = 16.30 MPa Beams = 8KN/m³, F = 1.10 MPa E = 10,300 MPa,…

Q: Design a simply-supported one-way slab to carry a uniformly distributed live load of 600 psf. The…

A: One-way slab: If the ratio of longer span to the shorter span is equal to or greater than two then…

Q: needs a foundation designed. Girders will be placed at 4' o.c. ith support every 8'. what weight…

A: Given:- Girders will be placed at 4' o.c. ith support every 8'. To find:- what weight will the…

Q: Given. A shear wall 24 ft. long and in. thick with a floor-to-floor height of It. Compressive…

Q: Determine the reinforcement required of a beam cross section shown in the Figure of ? = 400??,? =…

Q: 20-mm diameter bonded steel reinforcement needed to satisfy the NSCP requirements. Place the steep…

Q: Find the axial stress (in psi) of the steel. " Your answer Find the axial stress (in psi) of the…

Q: Discuss various loads and load combinations to be considered in the design of a roof truss

A: There are 4 types of loads that should be considered when designing a roof truss.Dead load : Dead…

Q: Trace the loads through the 2-story structure and show all of the appropriate FBD's of the major…

Q: In the design of corbel beams in a pumping station, why are shear links designed in the top 2/3 of…

A: Introduction - The corbel beams are those which have Zd < 0.6 Here, Z = The distance of bearing…

Q: a) Design the rectangular beam to resist the applied moment. DL=20kN/m, LL=15kN/m. Use C25,S420;…

A: Answer (a)To design the rectangular beam based on the given data we need to calculate the Design…

Q: Wo does not include beam weight PL=lo kiPs = 2 kip/ft W = 4 kip/ft %3D 3 # 11 bars (A) 2 in.…

A: Compressive strength of concrete (fc') = 5000 psiYield strength of steel (fy) = 60000 psiUnit weight…

Q: alculate the number of 3,000-lb form-ties required for a built-up wooden formwork for a concrete…

A: The compressive stress is the pressure that deforms the material to diminish the material volume.…

Q: 3 in. in. 2 in. i in. 2 in. i in. Prob. 9-66

A: The location y¯ of the Centroid for a beam having the cross section area is shown. The beam is…

Q: A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are…

A: To find:maximum moment about major axis in N-m

Q: 6.1 A four-span one-way slab is supported on 12-in.-wide beams with center- to-center spacing of 14,…

A: depicts a four-span one-way slab supported on 12-inch wide beams with a center-to-center spacing of…

Q: An 85-mm thick precast concrete slab is lifted by 4 – 16 mmø cables as shown. Unit weight of…

A: from fig :x=1.52+1.52=2.12mθ=tan-122.121=43.314°

Q: Determine the force in each member due to dead load, and rain loads.

Q: A one-way interior slab panel, continuous on both ends, is built integrally with the beam supports.…

A: Unsupported span length(L)=3.2 m, Total factored uniformly distributed load(w)=11.2 kpa, Concrete…

Q: Check the safety of the square footing as given to support the applied axial loads only neglecting…

A: column dimesion = 500mm, 500mm Soil pressure = 190 KN/m2Fck = 21 N/mm2Fy = 276 N/mm2foundation…

Q: 3. Design a one-way floor simply supported slab (16ft x 35 ft) in size to carry a uniform live load…

A: Given,fy=50000 psiLive LoadL.L.=500 psff'c=4000 psiSlab span=16 feetLB=3516>2 i.e. One way…

Q: Solve for the concrete materials of slab, beams and girders using class "A" concrete.

Q: A 24-inch square reinforced concrete column with tied transverse reinforcement is being considered…

A: Answer (a) Calculation of minimum permissible area and maximum permissible area of vertical…

Q: For the beam and loading shown determine the max required width b knowing that for the grade of…

Q: View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of…

Q: Design a one-way floor simply supported slab (16ft x 35 ft) in size to carry a uniform live load of…

A: Consider the given data to Design a one way slab fc'=4000 psiSteel grade =fy=5000 psiLive…

Q: 1. The reinforced concrete cantilever retaining wall in Figure 1 is made with 3000 psi normalweight…

A: The objective of the question is to calculate the development length for the main reinforcement of a…

Q: Q3/B: There are different objections for wooden supports, list them.

A: Objections for wooden supports are listed below:

Q: he beam shown has a 30-ft. simple span; f’c = 5,000 psi, fps = 250,000 psi, and the initial…

A: Given Data :

Q: a) A simply supported beam carrying plaster is to span 5m and support uniformly distributed…

A: Given data:- Length of simply supported beam, L=5 m Uniformly distributed characteristic dead loads,…

Q: Determine the preliminary structural plan for a 10-story (plus a roof) steel residential building…

A: To determine the preliminary sizing and layout for the office building, determine the spacing of the…

Q: B. for the floor system shown below with assuming that service dead load 3 kN/m2, live load 4 kN/m2,…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Describe about the slab–buttress structure.

A: - In slab buttress structure, a slab in the form of deck is provided which get support from the…

Q: Where should the primary longitudinal reinforcement be placed in a cantilever beam? Near the top of…

A: Tensile stresses are applied to the top fibres of the cantilever beam, which are located above the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Using the sketches and notes explain the two ways steel joist are usually braced against instability?
Please solve it ASAP will give an upvote for sure
1. A rectangular beam section is 10 in. wide and has a structural depth of 13.5 in. Reinforcement consists of two No. 8 bars. Given that the strength normal weight concrete is 4000 psi and there is NO shear reinforcement in the section, determine the nominal shear capacity allowed by the ACI Code. (5 pt) (Hint: No web reinforcement, so Vc = 8λ¸^(pw)¹/³√fcbwd shall be used).
1. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 a. Considering sag rods and tie rods at midspan, what is the maximum moment about major axis in N-m? (2 decimal places) b. Considering sag rods and tie rods at midspan, what is the maximum moment about minor axis in N-m? (2 decimal places) c. Considering sag rods and tie rods at midspan, what is the interaction value for combined moment? (2 decimal places)
draw provide a 350x350 mm size concrete pier with a height of 900 mm from the concrete slab and reinforced with 8-16 mm diam. v.b. & 10 mm ties spaced 1 @50, 4 @100,rest @ 150 mm oc.
Trimmers provide the support necessary to transfer the load carried by the headers to the foundation. True O False
The reinforced concrete cantilever retaining wall is made with 3000 psi normal weight concrete and reinforced with Grade 60 galvanized steel. the main reinforcement rests flexural stresses in the stem and is specified as #7 bars every 18 inches along the length of the wall. The distribution seal distributes stresses along the length of the wall and is specified as #4 bars at 12 I spacing. The concrete cover is 1.5 everywhere. Calculate the developmental length for the main reinforcement using the basic equation (ACI 318 -19: 25.4.2.4). Assume no transverse reinforcement Ktr-->0). Is the main reinforcement embedded deeply enough in the footing to fully develop its yield strength in tension?
2. Roof joists are spaced at 2m and span 6m between supporting girders, and joist depth of 600mm. The allowable deflection limits for OWSJ are L/360 under snow load. The OWSJS are subjected to a dead load of 2.96kPa which includes the estimate joist weight of 0.15kPa, an occupancy load of 2.4kPa, and the following: SULS 1.99kPa SSLS = 1.25kPa Select a suitable OWSJ which satisfies the limit states design.
5) For the following concrete beam, sketch where the rebar should be placed. ( 5' 1000 lbs. 5' 5' 4000 lbs. 5' 1000 lbs.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown and w = 663.2 lb/ft. If the allowable strength of the glue in shear is 105 psi, Determine:(b) the shear stress in the glue joint at H, which is located 4.5 in. above the bottom of the beam and at a distance of x = 86 in. from the left support. Assume that the beam is subjected to the load w determined in part (a). [Answer: τH = 19.34 psi]
A big box retail store is built with CMU bearing walls around its perimeter. The store measures 450 ft across the front and back and 360 ft across the sides. The walls are 28 ft tall and are reinforced horizontally with truss bars in alternate courses and vertically with #4 bars 32 in. on-center. There is an 8” tall bond beam running around the full perimeter of the building at the roof level (24 ft) to support the roof framing. The openings in the CMU walls, and the associated lintels are as follows: Opening Location Quantity Size Lintel Lintel Rebar Door Front wall 2 8’-0” x 10’-0” 16” tall CMU 2, #4 Door Side wall 2 each side 8’-0” x 4’-0” 8” tall CMU 1, #4 Door Back wall 3 8’-0” x 9’-0” 16” tall CMU 2, #4 Window Side wall 2 4’-0” x 3’-0” 8” tall CMU 1, #4 Note: each lintel should be a multiple of 8” long and have 8” of bearing on each side of the opening. Opening sizes are listed as height x width…
i need the answer quickly