Answered: Determine the tensile stress developed…

Determine the tensile stress developed in member AB due to a load of P = 500 lb at D. The member AB is thick and 2" wide. 2'x2" TENSION MEMBER 1A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
9. Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each member is 3780 mm². Indicate whether the stresses are tensile (T) or compressive (C). BC = 4.44 MPa (C), BE = 3.45 MPa (T) B C 50° 50° 50⁰° E 20 KN 50% D
Link AC has a uniform rectangular cross section 1/8 in. thick and1 in. wide. Determine the normal stress in the central portion of the link.
3. Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P=75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m-°C, Aa = 850 mm2 Es = 210 GPa, as = 11.9 um/m-°C and As = 650 mm² . %3D %3D Steel Aluminum 3m 2.5m 3 m 3 m 3 m 75 KN
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
Find the maximum load w applied if the allowable bending stress is 70 Mpa
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
Q3 (25%): Determine the force in members CD, CF, and CG, shown in Figure 3, and state if these members are in tension or compression. SAN 3KN Figure 3