Determine the reliability between Devices A and B shown in Figure 1. Step-by-step calculations must be given. Also propose a design that can achieve 5-nines reliability. Assume that switches’ and routers’ reliability are 99.0% and 98.5%, respectively. The reliability of WAN A, WAN B and WAN C is shown in the figure. Note that the proposed design should utilize as low new switches or routers or WAN networks as possible.

Q: If the throughput of slotted aloha is 10 % more than the pure aloha while transmitting the data on…

A: Introduction :

Q: Question 5 You are designing a Wi-Fi cell for coverage in the 5 GHz band. Assume low ceilings (for…

A: You are designing a Wi-Fi cell for coverage in the 5 GHz band.Assume low ceilings.Note the following…

Q: 1. Suppose, some students of BRACU have opened a new telecommunication company named "BRACTel". They…

A: Given, =>Number of channels = 4 channels =>Bandwidth of each channel = 70 Mbps =>Number of…

Q: video signals are to be combined 20 for 8-bit PCM system with 1200 voice messages of range of (6 to…

A: ANSWER:-

Q: a) You have been hired by a startup company to design, plan, and implement an Ethernet network. The…

A: Given: You have been hired by a startup company to design, plan, and implement an Ethernet network.…

Q: 4. Please show all work! Switched virtual circuit transmission overhead could be high to send a…

A: To calculate the minimum time to transmit one ATM cell from Miami to San Francisco on a basic SONET…

Q: 1. each UE-1 and UE-2 when equal bandwidth (OMA schemes) 2. each UE-1 and UE-2 when the user is…

A: NOMA (Non orthogonal multiple access):- It has higher spectral efficiency as compared to OMA. Has…

Q: Given the same 4-link network, OD flow rate of 9, and link travel time functions, use incremental…

A:

Q: Consider the following transport network 300 100 400 550 300 150 300 500 400 c. Find the maximum…

A: C.  D.

Q: Consider a 2 user CDMA wireless communication system with P, (dB) = P, (dB) jn = 15 dB. Given noise…

A: Answer 1) SNR(signal to noise ratio)= signal power/ noise power SNR(in dB)= 10 log10 (signal power/…

Q: The maximal-flow technique would best be used   a. to determine the number of units to ship from…

A: Maximize flow technique is said to be a technique which tells that what is the maximum amount of…

Q: a) show all cell that are co-channel cells with cell x if GSM technology is used with a reuse factor…

A:

Q: Problem 1. We want to design a communications link with 8 PSK waveform. The channel BW is at most 80…

A: We want to design a communications link with 8 PSK waveform. The channel BW is at most 80 MHz and…

Q: The city of Nizwa has an area of 1400 square miles and is covered by a cellular system using a…

A: We have : Given the Radius of a cell = 4 miles. Area measured by cell = 50 square miles Area…

Q: a. Discuss the key performance indicators in data communication that stimulate network performance…

A: Given: a. Discuss the key performance indicators in data communication thatstimulate network…

Q: For a transmission medium, SNRdb is given as 18. The given capacity of 28,26 Mbps is valid for which…

A: Given SNRdb=18 Capacity=28,26Mbps We need to calculate bandwidth and amount of signal level.

Q: what is the number of cable links required for logy?

A: For n devices in a network, what is the number of cable links required for a mesh, ring, bus, and…

Q: Consider the speed of propagation of a signal along a cable is 2 x 108 m/s and network has 10 Mbps…

A: Introduction

Q: 13. Suppose a 1-Gbps point-to-point link is being set up between th Earth and a new lunar colony.…

A:

Q: What is the optimal value for SWS? Consider three nodes A, B, C connected in series. Node A is…

A: The Answer is

Q: 22/lf a total of 33 MHz of bandwidth is allocated to a particular FDD cellular telephone system…

A:

Q: 1- TI carrier system is used: a For PCM voice transmission b. For frequency modulated signals e. For…

A: Disclaimer: "Since you have asked multiple question, we will solve the first question for you. If…

Q: 19 10 Mbps half-duplex ethernet network consists of two segments connected by a repeater. It…

A: According to collision detection in half duplex ethernet.  Tt >= 2* TP  Here we have given the…

Q: While installing fiber optics, some companies will install a SONET ring; a full loop of cable…

A: The circuit that will have the minimum cost using the sorted edges will be found out using the…

Q: Q1. The network in figure 01 is a portion of an office network of a reputed organization. Answer the…

A: The solution is

Q: (a) Explain the differences among the mode of operations of bridges, hubs, routers and repeaters.…

A:

Q: (a) Explain why line codes are used? Draw appropriate diagrams to illustrate the following…

A: A line code is the code used for data transmission of a digital signal over a transmission line.…

Q: Consider an ethernet with length of the cable is 1800 meter and speed of the signal cable is 3 x…

A: We are going to find out idle% of a channel where ethernet has length 1800 meter and speed is 3*108.…

Q: 5 points  Find the latency of Token Ring (in bits) where data rate of link is 20 Mbps and 40…

A:

Q: You have a network of four nodes and three links: A B C D A message of size 1,024,000 bits is to be…

A: Given that, Number of hops = 3 Size of message= 1,024,000 bits /8 =128000 Bandwidth for first two…

Q: For error detection is used by the Select following multiple access protocol that are fall under…

A: For the above multiple questions, rather than searching for correct answers, its better to cancel…

Q: For simplicity, let's assume that a voice channel has an 8-kilohertz bandwidth. It is necessary to…

A: As it is said in the question: Channel bandwidth=8KHz  Guard bands=1000Hz=1KHz  Number of channels…

Q: How can the effect of each issue 1) Delay Latency, 2) Network Jitter, and 3) Packt Loss be minimized…

A: Introduction: Here we are required to explain how can the effect of Delay Latency, 2) Network…

Q: 16 12 10

A: The critical path of a network is found by using two methods: Forward Pass Backward Pass   First,…

Q: Question 5  (b)Construct the Routing Table for core router  Full explain this question and text…

A: Routing refers to Subnetting in the networking.  Before reading this article, make sure you read the…

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.