For error detection is used by the Select following multiple access protocol that are fall under channelization protocol. Note: May have more than 1 answer None of the above FDMA CSMA/CA TDMA CDMA ALOHA Polling CSMA/CD Consider a noiseless channel with a bandwidth of 8 KHz. If we want to transmit 24 Kbps on this channel, the minimum number of signal levels we need is Note: May have more than 1 answer 16 8 2 12 None of the above The received CRC C(7.4) codeword is 1010110, is this corrupted or uncorrupted? Note: May have more than 1 answer None of the above Corrupted Uncorrupted

For error detection is used by the Select following multiple access protocol that are fall under channelization protocol. Note: May have more than 1 answer None of the above FDMA CSMA/CA TDMA CDMA ALOHA Polling CSMA/CD Consider a noiseless channel with a bandwidth of 8 KHz. If we want to transmit 24 Kbps on this channel, the minimum number of signal levels we need is Note: May have more than 1 answer 16 8 2 12 None of the above The received CRC C(7.4) codeword is 1010110, is this corrupted or uncorrupted? Note: May have more than 1 answer None of the above Corrupted Uncorrupted

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 19VE

See similar textbooks

Similar questions

The maximum window size for data transmission using the selective reject protocol with n-bit frame sequence numbers is: 0
Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During each time slot 8 bits are sent. What is the shortest time possible (in seconds) to transmit a 1 Mbyte file over the given link?
We have a 1000 m long 10 Mbps communication channel with ARQ protocol. The signal travels at a speed of 2 ∗ 10 ^ 8 ? / ?Assume that no frame is lost or damaged. Confirmation frames, control information are negligible in size.For what range of frame sizes do we get an efficiency of at least 70%?
If transmission time is 5ms and propagation delay is 12ms then draw the complete ‘Stop-and-Wait Flow Control’ with both flow of frame and acknowledgment. Do the similar job for transmission time of 12ms and propagation delay of 5ms.
The timer of a system using the Stop-and-Wait ARQ Protocol has a time-out of 6ms and round trip time RTT is 4ms. Assume the acknowledgment of first frame is delayed by 4ms and the third frame is received in error one time. All other frames and acknowledgement are received correctly .Draw the flow diagram for four frames. (please draw it clearly with all detailes what happen in each frame)
Discuss the main difference(s) between sliding window (e.g., Go-Back_N) protocol and the Simplex Stop-and-Wait protocol for a noisy channel protocol
A digitized voice channel is made by digitizing a 4-kHz bandwidthanalog voice signal. We need to sample the signal at twice the highestfrequency. We assume that each sample requires 16 bits. What is therequired bit rate?
Given a home wireless IEEE 802.11AC Wi-Fi channel with a bandwidth of 80 MHz, a) Apply the real time streaming transmission of a video that samples at 40 frames/second and each frame has a resolution of 800x600 pixels. Each pixel has its colour presented in 16 bits. Calculate the required transmission rate. b) If the Wi-Fi Channel is very noisy with an acceptable Signal-to-Noise Ratio of 10dB, does the video streaming in part (a) still possible without any distortion? (provide workings)
Consider the following scenario: Frames of 12000 bits are sent over a 400kbps channel using a satellite whose propagation delay is 270ms. Acknowledgements are always piggybacked onto data frames. (That is, in the case of stop-and-wait, the next frame cannot be transmitted until the entire frame containing the acknowledgement is received.) Five-bit sequence numbers are used. What is the maximum achievable channel utilization for (a) Stop-and-wait. (b) Protocol 5 (i.e., Go Back N). (c) Protocol 6 (i.e., Selective Repeat)
Your challenge is to use MATLAB to plot a received signal at a base station in a multipath channel when the transmitter sends a sinusoidal carrier signal. A transmitter sends a sinusoidal signal of frequency 1.5 MHz to the base station. There is a line-of-sight (LoS) path to the base station receiver, with delay 1 usec. The signal on this path is attenuated in amplitude by a factor 0.9 (the LoS amplitude gain). There are also three single bounce paths, one of delay 2 usec, with an amplitude gain of 0.5, one of delay 7 usec, with an amplitude gain of 0.4, and a third of delay 10 usec, with amplitude gain of 0.2. These parameters are fixed and do not change during the transmission. The project is to write MATLAB code to obtain the signal received at the receiver. Plot the signal over a time interval of 20 usec, including axes, and provide units for the time axis. Then answer the following questions: a) How is the output signal frequency related to the input signal frequency? b) Does the…
Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem3. Consider a digital multimedia transmission system. Separate audio and video coders are used to encode these signals. Audio and video bits are packed in packets together and transmitted over a transmission link. Each packet is 2,000 bytes long, which includes a 48-byte header. The system generates one packet every 40 ms. Calculate the following values:a. The minimum data transmission rate required to support the above system.b. The minimum signal-to-noise ratio (SNR) in dB required to transmit the above audio and video information. Assume a 400-kHz transmission channel bandwidth is used.c. The end-to-end packet delay over a 50-km link, using answer in Part a).
A telephone modem is used to connect a personal computer to a host computer. The speed of the modem is 56 kbps, the one-way propagation delay is 100 ms, the packet size is 256 bytes, and the probability of an error in a packet is 10^-4. Find the efficiency of stop-and-wait ARQ. What window size N is needed to keep the channel busy when there are no transmission errors. For this window size finds the efficiency of the go-back-N and selective repeat protocols. Note: Correct and detailed answer will be Upvoted else downvoted