Determine the pushover curve of the 30x50 cm size column given in the figure. Consider the first order (moment only) and second order (including the P-5 effect) effects while calculating the base shear and plot the pushover curves on the same graph. The column is working on its strong axis. Consider the plastic hinge length as the half of the depth of the column. Hint: Plastic curvature- Ultimate Curvature- Yield Curvature Parameters and Materials: a) C25/S420, Es-200000 MPa, As-As- 3020 924 mm², Ecu-0.004, Ey-0.0021, fc-25 MPa, fy=420 MPa, Po 1500 kN

Determine the pushover curve of the 30x50 cm size column given in the figure. Consider the first order (moment only) and second order (including the P-5 effect) effects while calculating the base shear and plot the pushover curves on the same graph. The column is working on its strong axis. Consider the plastic hinge length as the half of the depth of the column. Hint: Plastic curvature- Ultimate Curvature- Yield Curvature Parameters and Materials: a) C25/S420, Es-200000 MPa, As-As- 3020 924 mm², Ecu-0.004, Ey-0.0021, fc-25 MPa, fy=420 MPa, Po 1500 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.375 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) Determine the maximum tensile stress omay and the maximum in-plane shear stress Tmay in the wall of the cylinder. (Enter the magnitudes in ksi.) o, = ksi Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
Help please!
A vertical tapered rod of length L has its diameter varying linearly from 'd' at lower end to D at the upper end which has fixed support. Young's modulus of the material is E. Show that the elongation 4FL of the rod at its lower end when subjected to a longitudinal force Fis given by 8 TdDE
Tb = 80.51
Q .A beam has a force of 25kN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y - y plane for positions A to F, c) plot the shear stress distribution on a suitable graph, labelling the principal values cross-section as shown in Figure Q. The beam is subjected to a vertical shearing Centre of Gravity X y 30 mm 180 mm y A B -C.-. -E- 10mm x 5mm Figure Q: Beam cross-section 30 mm 10 mm
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
A beam has a cross-section as shown in Figure Q5. The beam is subjected to a vertical shearing force of 100KN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y – y plane, c) plot the shear stress distribution on a suitable graph, labelling the principal values. y! Centre of Gravity. y' 30 тm 60 тm шш 09 120 тт
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: F w (x) = E, ( - +4) %3D Ely 8. The value of E is 200,000 Nmm 2 and the values of ly is 20 x 106 mm4 The maximum value of z for the beam cross section is 20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm? Express your answer in Nmm2, as a number to 2 dp, without the units.
Question 1 A beam is undergoing bending deformation, whose cross-section is shown in Figure Q1. a) Determine the cross-sectional properties lxx, lyy and Iy. b) Determine the direct (bending) stress distribution in the section beam, produced by a positive bending moment, M,. The cross-section is anti-symmetric with centroid at the mid-point of the vertical web. No moment is applied about the y-axis, i.e. M, = 0. 2 2 M. 2 h 2 Figure Q1
1) a Compressor with a diameter of 0,65 metres and a thickness (t)= 4mm Sigmax= 42 MPA and Sigmay=84MPA Calculate: The pressure P and Maximum In-Plane Shear Stress Tmaxvlak in MPA 2) an element has undergoing a rotation of Theta= 30 degrees Sigmax= 75 MPA and sigma y= 55 MPA. Calculate X', Y' and Txy" in MPA 3) A uniform Beam with a lenght of 2 metres to a-a and forces N=12kn and V=4kn. Calculate the main stresses sigma1 and sigma 2 [in MPA] 4) an element with the given stresses: Sigmax=75 MPA and Sigmay= 55 MPA Calculate the Absolute maximum shear stress in MPA )Tabsmax)